/branches/18.06.1/target/linux/ramips/dts/GL-MT300N-V2.dts |
@@ -0,0 +1,151 @@ |
/dts-v1/; |
|
#include "mt7628an.dtsi" |
|
#include <dt-bindings/gpio/gpio.h> |
#include <dt-bindings/input/input.h> |
|
/{ |
compatible = "glinet,gl-mt300n-v2", "mediatek,mt7628an-soc"; |
model = "GL-MT300N-V2"; |
|
aliases { |
led-boot = &led_power; |
led-failsafe = &led_power; |
led-running = &led_power; |
led-upgrade = &led_power; |
}; |
|
chosen { |
bootargs = "console=ttyS0,115200"; |
}; |
|
memory@0 { |
device_type = "memory"; |
reg = <0x0 0x8000000>; |
}; |
|
leds { |
compatible = "gpio-leds"; |
|
led_power: power { |
label = "gl-mt300n-v2:green:power"; |
default-state = "on"; |
gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; |
}; |
|
wan { |
label = "gl-mt300n-v2:green:wan"; |
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; |
}; |
|
wlan { |
label = "gl-mt300n-v2:red:wlan"; |
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; |
}; |
}; |
|
keys { |
compatible = "gpio-keys-polled"; |
poll-interval = <20>; |
|
reset { |
label = "reset"; |
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RESTART>; |
}; |
|
BTN_0 { |
label = "BTN_0"; |
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
linux,code = <BTN_0>; |
}; |
|
BTN_1 { |
label = "BTN_1"; |
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; |
linux,code = <BTN_1>; |
}; |
}; |
|
gpio_export { |
compatible = "gpio-export"; |
#size-cells = <0>; |
|
usb { |
gpio-export,name = "usb"; |
gpio-export,output = <1>; |
gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; |
}; |
}; |
}; |
|
&pinctrl { |
state_default: pinctrl0 { |
gpio { |
ralink,group = "wdt", "gpio", "wled_an", "p0led_an", "p1led_an", "i2s"; |
ralink,function = "gpio"; |
}; |
}; |
}; |
|
ðernet { |
mtd-mac-address = <&factory 0x4>; |
}; |
|
&wmac { |
status = "okay"; |
ralink,mtd-eeprom = <&factory 0x0>; |
}; |
|
&spi0 { |
status = "okay"; |
|
m25p80@0 { |
compatible = "jedec,spi-nor"; |
reg = <0>; |
spi-max-frequency = <10000000>; |
|
partitions { |
compatible = "fixed-partitions"; |
#address-cells = <1>; |
#size-cells = <1>; |
|
partition@0 { |
label = "u-boot"; |
reg = <0x0 0x30000>; |
read-only; |
}; |
|
partition@30000 { |
label = "u-boot-env"; |
reg = <0x30000 0x10000>; |
read-only; |
}; |
|
factory: partition@40000 { |
label = "factory"; |
reg = <0x40000 0x10000>; |
read-only; |
}; |
|
partition@50000 { |
compatible = "denx,uimage"; |
label = "firmware"; |
reg = <0x50000 0xfb0000>; |
}; |
}; |
}; |
}; |
|
&uart1 { |
status = "okay"; |
}; |
|
&ehci { |
status = "okay"; |
}; |
|
&ohci { |
status = "okay"; |
}; |