/branches/18.06.1/target/linux/ramips/dts/F5D8235_V2.dts |
@@ -9,21 +9,11 @@ |
compatible = "belkin,f5d8235-v2", "ralink,rt3052-soc"; |
model = "Belkin F5D8235 v2"; |
|
aliases { |
led-boot = &led_router; |
led-failsafe = &led_router; |
led-running = &led_router; |
led-upgrade = &led_router; |
}; |
|
cfi@1f000000 { |
compatible = "cfi-flash"; |
reg = <0x1f000000 0x800000>; |
bank-width = <2>; |
device-width = <2>; |
|
partitions { |
compatible = "fixed-partitions"; |
#address-cells = <1>; |
#size-cells = <1>; |
|
@@ -34,7 +24,6 @@ |
}; |
|
partition@50000 { |
compatible = "denx,uimage"; |
label = "firmware"; |
reg = <0x50000 0x790000>; |
}; |
@@ -49,7 +38,6 @@ |
reg = <0x7f0000 0x10000>; |
}; |
}; |
}; |
|
rtl8366rb { |
compatible = "realtek,rtl8366rb"; |
@@ -57,7 +45,7 @@ |
gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
}; |
|
leds { |
gpio-leds { |
compatible = "gpio-leds"; |
|
internet { |
@@ -80,7 +68,7 @@ |
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
}; |
|
led_router: router { |
router { |
label = "f5d8235-v2:blue:router"; |
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
}; |
@@ -88,8 +76,6 @@ |
storage { |
label = "f5d8235-v2:blue:storage"; |
gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; |
trigger-sources = <&otg_port1>; |
linux,default-trigger = "usbport"; |
}; |
|
storage2 { |
@@ -112,7 +98,7 @@ |
&pinctrl { |
state_default: pinctrl0 { |
gpio { |
ralink,group = "spi", "i2c", "jtag", "mdio", "uartf"; |
ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf"; |
ralink,function = "gpio"; |
}; |
}; |
@@ -120,21 +106,10 @@ |
|
ðernet { |
mtd-mac-address = <&uboot 0x40004>; |
pinctrl-names = "default"; |
pinctrl-0 = <&rgmii_pins>; |
}; |
|
&esw { |
ralink,rgmii = <1>; |
mediatek,portmap = <0x3f>; |
ralink,fct2 = <0x0002500c>; |
/* |
* ext phy base addr 31, rx/tx clock skew 0, |
* turbo mii off, rgmi 3.3v off, port 5 polling off |
* port5: enabled, gige, full-duplex, rx/tx-flow-control |
* port6: enabled, gige, full-duplex, rx/tx-flow-control |
*/ |
ralink,fpa2 = <0x1f003fff>; |
}; |
|
&wmac { |