| /branches/18.06.1/target/linux/ramips/dts/EX3700.dts |
|---|
| @@ -11,21 +11,14 @@ |
|---|
| compatible = "netgear,ex3700", "ralink,mt7620a-soc"; |
| model = "Netgear EX3700/EX3800"; |
| |
| aliases { |
| led-boot = &led_power_green; |
| led-failsafe = &led_power_green; |
| led-running = &led_power_green; |
| led-upgrade = &led_power_green; |
| }; |
| |
| chosen { |
| bootargs = "console=ttyS0,57600"; |
| }; |
| |
| leds { |
| gpio-leds { |
| compatible = "gpio-leds"; |
| |
| led_power_green: power_g { |
| power_g { |
| label = "ex3700:green:power"; |
| gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; |
| default-state = "on"; |
| @@ -34,6 +27,7 @@ |
|---|
| power_a { |
| label = "ex3700:amber:power"; |
| gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; |
| default-state = "off"; |
| }; |
| |
| router_g { |
| @@ -62,8 +56,10 @@ |
|---|
| }; |
| }; |
| |
| keys { |
| gpio-keys-polled { |
| compatible = "gpio-keys-polled"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| poll-interval = <20>; |
| |
| reset { |
| @@ -92,50 +88,45 @@ |
|---|
| status = "okay"; |
| |
| m25p80@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <10000000>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| partition@0 { |
| label = "u-boot"; |
| reg = <0x0 0x30000>; |
| read-only; |
| }; |
| |
| partition@0 { |
| label = "u-boot"; |
| reg = <0x0 0x30000>; |
| read-only; |
| }; |
| partition@30000 { |
| label = "config"; |
| reg = <0x30000 0x10000>; |
| read-only; |
| }; |
| |
| partition@30000 { |
| label = "config"; |
| reg = <0x30000 0x10000>; |
| read-only; |
| }; |
| factory: partition@40000 { |
| label = "factory"; |
| reg = <0x40000 0x10000>; |
| read-only; |
| }; |
| |
| factory: partition@40000 { |
| label = "factory"; |
| reg = <0x40000 0x10000>; |
| read-only; |
| }; |
| partition@50000 { |
| label = "firmware"; |
| reg = <0x50000 0x790000>; |
| }; |
| |
| partition@50000 { |
| compatible = "denx,uimage"; |
| label = "firmware"; |
| reg = <0x50000 0x790000>; |
| }; |
| partition@7e0000 { |
| label = "board_data"; |
| reg = <0x7e0000 0x10000>; |
| read-only; |
| }; |
| |
| partition@7e0000 { |
| label = "board_data"; |
| reg = <0x7e0000 0x10000>; |
| read-only; |
| }; |
| |
| partition@7f0000 { |
| label = "nvram"; |
| reg = <0x7f0000 0x10000>; |
| read-only; |
| }; |
| partition@7f0000 { |
| label = "nvram"; |
| reg = <0x7f0000 0x10000>; |
| read-only; |
| }; |
| }; |
| }; |
| @@ -142,13 +133,14 @@ |
|---|
| |
| &pcie { |
| status = "okay"; |
| }; |
| |
| &pcie0 { |
| mt76@0,0 { |
| reg = <0x0000 0 0 0 0 >; |
| mediatek,mtd-eeprom = <&factory 0x8000>; |
| ieee80211-freq-limit = <5000000 6000000>; |
| pcie-bridge { |
| mt76@0,0 { |
| reg = <0x0000 0 0 0 0 >; |
| device_type = "pci"; |
| mediatek,mtd-eeprom = <&factory 0x8000>; |
| ieee80211-freq-limit = <5000000 6000000>; |
| }; |
| }; |
| }; |
| |
