| /branches/18.06.1/target/linux/ramips/dts/EX3700.dts |
|---|
| @@ -0,0 +1,162 @@ |
|---|
| /* This file is released into the public domain */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| #include "mt7620a.dtsi" |
| |
| / { |
| compatible = "netgear,ex3700", "ralink,mt7620a-soc"; |
| model = "Netgear EX3700/EX3800"; |
| |
| chosen { |
| bootargs = "console=ttyS0,57600"; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| |
| power_g { |
| label = "ex3700:green:power"; |
| gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; |
| default-state = "on"; |
| }; |
| |
| power_a { |
| label = "ex3700:amber:power"; |
| gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; |
| default-state = "off"; |
| }; |
| |
| router_g { |
| label = "ex3700:green:router"; |
| gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; |
| }; |
| |
| router_r { |
| label = "ex3700:red:router"; |
| gpios = <&gpio2 24 GPIO_ACTIVE_LOW>; |
| }; |
| |
| device_g { |
| label = "ex3700:green:device"; |
| gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; |
| }; |
| |
| device_r { |
| label = "ex3700:red:device"; |
| gpios = <&gpio2 21 GPIO_ACTIVE_LOW>; |
| }; |
| |
| wps { |
| label = "ex3700:green:wps"; |
| gpios = <&gpio2 27 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| gpio-keys-polled { |
| compatible = "gpio-keys-polled"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| poll-interval = <20>; |
| |
| reset { |
| label = "reset"; |
| gpios = <&gpio2 26 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_RESTART>; |
| }; |
| |
| wps { |
| label = "wps"; |
| gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_WPS_BUTTON>; |
| }; |
| }; |
| }; |
| |
| &gpio0 { |
| status = "okay"; |
| }; |
| |
| &gpio2 { |
| status = "okay"; |
| }; |
| |
| &spi0 { |
| status = "okay"; |
| |
| m25p80@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <10000000>; |
| |
| partition@0 { |
| label = "u-boot"; |
| reg = <0x0 0x30000>; |
| read-only; |
| }; |
| |
| partition@30000 { |
| label = "config"; |
| reg = <0x30000 0x10000>; |
| read-only; |
| }; |
| |
| factory: partition@40000 { |
| label = "factory"; |
| reg = <0x40000 0x10000>; |
| read-only; |
| }; |
| |
| partition@50000 { |
| label = "firmware"; |
| reg = <0x50000 0x790000>; |
| }; |
| |
| partition@7e0000 { |
| label = "board_data"; |
| reg = <0x7e0000 0x10000>; |
| read-only; |
| }; |
| |
| partition@7f0000 { |
| label = "nvram"; |
| reg = <0x7f0000 0x10000>; |
| read-only; |
| }; |
| }; |
| }; |
| |
| &pcie { |
| status = "okay"; |
| |
| pcie-bridge { |
| mt76@0,0 { |
| reg = <0x0000 0 0 0 0 >; |
| device_type = "pci"; |
| mediatek,mtd-eeprom = <&factory 0x8000>; |
| ieee80211-freq-limit = <5000000 6000000>; |
| }; |
| }; |
| }; |
| |
| ðernet { |
| mtd-mac-address = <&factory 0x28>; |
| }; |
| |
| &wmac { |
| ralink,mtd-eeprom = <&factory 0x0>; |
| }; |
| |
| &pinctrl { |
| state_default: pinctrl0 { |
| default { |
| ralink,group = "i2c", "rgmii2", "spi refclk"; |
| ralink,function = "gpio"; |
| }; |
| }; |
| }; |
