/branches/18.06.1/target/linux/ramips/dts/DIR-810L.dts |
@@ -0,0 +1,136 @@ |
/dts-v1/; |
|
#include "mt7620a.dtsi" |
|
#include <dt-bindings/gpio/gpio.h> |
#include <dt-bindings/input/input.h> |
|
/ { |
compatible = "dlink,dir-810l", "ralink,mt7620a-soc"; |
model = "D-Link DIR-810L"; |
|
gpio-keys-polled { |
compatible = "gpio-keys-polled"; |
#address-cells = <1>; |
#size-cells = <0>; |
poll-interval = <20>; |
|
reset { |
label = "reset"; |
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
linux,code = <BTN_0>; |
}; |
|
wps { |
label = "wps"; |
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
linux,code = <BTN_0>; |
}; |
}; |
|
gpio-leds { |
compatible = "gpio-leds"; |
|
power { |
label = "dir-810l:green:power"; |
gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; |
}; |
|
wan { |
label = "dir-810l:orange:wan"; |
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; |
}; |
|
status { |
label = "dir-810l:orange:power"; |
gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; |
}; |
}; |
}; |
|
&spi0 { |
status = "okay"; |
|
m25p80@0 { |
#address-cells = <1>; |
#size-cells = <1>; |
compatible = "jedec,spi-nor"; |
reg = <0>; |
spi-max-frequency = <10000000>; |
|
partition@0 { |
label = "u-boot"; |
reg = <0x0 0x30000>; |
read-only; |
}; |
|
partition@30000 { |
label = "u-boot-env"; |
reg = <0x30000 0x10000>; |
read-only; |
}; |
|
factory: partition@40000 { |
label = "factory"; |
reg = <0x40000 0x10000>; |
read-only; |
}; |
|
factory5g: partition@50000 { |
label = "factory5g"; |
reg = <0x50000 0x10000>; |
read-only; |
}; |
|
partition@60000 { |
label = "Wolf_Config"; |
reg = <0x60000 0x10000>; |
read-only; |
}; |
|
partition@70000 { |
label = "MyDlink"; |
reg = <0x70000 0x80000>; |
read-only; |
}; |
|
partition@e0000 { |
label = "Jffs2"; |
reg = <0xe0000 0x80000>; |
read-only; |
}; |
|
partition@170000 { |
label = "firmware"; |
reg = <0x170000 0x690000>; |
}; |
}; |
}; |
|
&pinctrl { |
state_default: pinctrl0 { |
gpio { |
ralink,group = "mdio", "rgmii1", "i2c", "wled", "uartf"; |
ralink,function = "gpio"; |
}; |
}; |
}; |
|
ðernet { |
mtd-mac-address = <&factory 0x28>; |
mediatek,portmap = "llllw"; |
}; |
|
&gsw { |
mediatek,port4 = "ephy"; |
pinctrl-names = "default"; |
pinctrl-0 = <&ephy_pins>; |
}; |
|
&pcie { |
status = "okay"; |
}; |
|
&wmac { |
ralink,mtd-eeprom = <&factory 0>; |
}; |