/branches/18.06.1/target/linux/ramips/dts/DIR-300-B1.dts |
@@ -0,0 +1,122 @@ |
/dts-v1/; |
|
#include "rt3050.dtsi" |
|
#include <dt-bindings/gpio/gpio.h> |
#include <dt-bindings/input/input.h> |
|
/ { |
compatible = "dlink,dir-300-b1", "ralink,rt3050-soc"; |
model = "D-Link DIR-300 B1"; |
|
aliases { |
led-boot = &led_status_green; |
led-failsafe = &led_status_green; |
led-running = &led_status_green; |
led-upgrade = &led_status_green; |
}; |
|
cfi@1f000000 { |
compatible = "cfi-flash"; |
reg = <0x1f000000 0x800000>; |
bank-width = <2>; |
device-width = <2>; |
|
partitions { |
compatible = "fixed-partitions"; |
#address-cells = <1>; |
#size-cells = <1>; |
|
partition@0 { |
label = "u-boot"; |
reg = <0x0 0x30000>; |
read-only; |
}; |
|
devdata: partition@30000 { |
label = "devdata"; |
reg = <0x30000 0x10000>; |
read-only; |
}; |
|
factory: partition@40000 { |
label = "devconf"; |
reg = <0x40000 0x10000>; |
read-only; |
}; |
|
partition@50000 { |
compatible = "denx,uimage"; |
label = "firmware"; |
reg = <0x50000 0x3b0000>; |
}; |
}; |
}; |
|
keys { |
compatible = "gpio-keys-polled"; |
poll-interval = <20>; |
|
reset { |
label = "reset"; |
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RESTART>; |
}; |
|
wps { |
label = "wps"; |
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_WPS_BUTTON>; |
}; |
}; |
|
leds { |
compatible = "gpio-leds"; |
|
status { |
label = "dir-300-b1:amber:status"; |
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
}; |
|
led_status_green: status2 { |
label = "dir-300-b1:green:status"; |
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
}; |
|
wan { |
label = "dir-300-b1:amber:wan"; |
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; |
}; |
|
wan2 { |
label = "dir-300-b1:green:wan"; |
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
}; |
|
wps { |
label = "dir-300-b1:blue:wps"; |
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
}; |
}; |
}; |
|
&pinctrl { |
state_default: pinctrl0 { |
gpio { |
ralink,group = "i2c", "spi", "jtag", "mdio", "rgmii", "uartf"; |
ralink,function = "gpio"; |
}; |
}; |
}; |
|
ðernet { |
mtd-mac-address = <&devdata 0x4004>; |
}; |
|
&esw { |
mediatek,portmap = <0x2f>; |
}; |
|
&wmac { |
ralink,mtd-eeprom = <&devdata 0x4000>; |
}; |