| /branches/18.06.1/target/linux/ramips/dts/DAP-1522-A1.dts |
|---|
| @@ -0,0 +1,149 @@ |
|---|
| /dts-v1/; |
| |
| #include "rt2880.dtsi" |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| compatible = "dlink,dap-1522-a1", "ralink,rt2880-soc"; |
| model = "D-Link DAP-1522 A1"; |
| |
| aliases { |
| led-boot = &led_status; |
| led-failsafe = &led_status; |
| led-running = &led_status; |
| led-upgrade = &led_status; |
| }; |
| |
| cfi@bc400000 { |
| compatible = "cfi-flash"; |
| reg = <0xbc400000 0x800000>; |
| bank-width = <2>; |
| device-width = <2>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "uboot"; |
| reg = <0x0 0x30000>; |
| read-only; |
| }; |
| |
| factory: partition@30000 { |
| label = "factory"; |
| reg = <0x30000 0x10000>; |
| read-only; |
| }; |
| |
| partition@40000 { |
| compatible = "wrg"; |
| label = "firmware"; |
| reg = <0x40000 0x3a0000>; |
| }; |
| }; |
| }; |
| |
| rtl8366s { |
| compatible = "realtek,rtl8366s"; |
| gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>; |
| gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| keys { |
| compatible = "gpio-keys-polled"; |
| poll-interval = <100>; |
| |
| reset { |
| label = "reset"; |
| gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_RESTART>; |
| }; |
| |
| wps { |
| label = "wps"; |
| gpios = <&gpio2 16 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_WPS_BUTTON>; |
| }; |
| |
| ap { |
| label = "ap"; |
| gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; |
| linux,code = <BTN_0>; |
| linux,input-type = <EV_SW>; |
| }; |
| |
| bridge { |
| label = "bridge"; |
| gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; |
| linux,code = <BTN_1>; |
| linux,input-type = <EV_SW>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| wps { |
| label = "dap-1522-a1:blue:wps"; |
| gpios = <&gpio2 17 GPIO_ACTIVE_LOW>; |
| }; |
| |
| ap { |
| label = "dap-1522-a1:blue:ap"; |
| gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; |
| }; |
| |
| sta { |
| label = "dap-1522-a1:red:sta"; |
| gpios = <&gpio2 19 GPIO_ACTIVE_LOW>; |
| }; |
| |
| led_status: status { |
| label = "dap-1522-a1:blue:status"; |
| gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| }; |
| |
| &gpio0 { |
| status = "okay"; |
| }; |
| |
| &gpio2 { |
| status = "okay"; |
| }; |
| |
| &pinctrl { |
| state_default: pinctrl0 { |
| gpio { |
| ralink,group = "i2c", "uartlite", "pci"; |
| ralink,function = "gpio"; |
| }; |
| }; |
| }; |
| |
| ðernet { |
| status = "okay"; |
| mtd-mac-address = <&factory 0x2004>; |
| |
| port@0 { |
| mediatek,fixed-link = <1000 1 1 1>; |
| }; |
| |
| mdio-bus { |
| status = "okay"; |
| |
| phy0: ethernet-phy@0 { |
| phy-mode = "mii"; |
| reg = <0>; |
| }; |
| }; |
| }; |
| |
| &wmac { |
| ralink,mtd-eeprom = <&factory 0x2000>; |
| }; |
