/branches/18.06.1/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-r7500.dts |
@@ -0,0 +1,382 @@ |
#include "qcom-ipq8064-v1.0.dtsi" |
|
#include <dt-bindings/input/input.h> |
#include <dt-bindings/soc/qcom,tcsr.h> |
|
/ { |
model = "Netgear Nighthawk X4 R7500"; |
compatible = "netgear,r7500", "qcom,ipq8064"; |
|
memory@0 { |
reg = <0x42000000 0xe000000>; |
device_type = "memory"; |
}; |
|
reserved-memory { |
#address-cells = <1>; |
#size-cells = <1>; |
ranges; |
rsvd@41200000 { |
reg = <0x41200000 0x300000>; |
no-map; |
}; |
}; |
|
aliases { |
serial0 = &gsbi4_serial; |
mdio-gpio0 = &mdio0; |
|
led-boot = &power_white; |
led-failsafe = &power_amber; |
led-running = &power_white; |
led-upgrade = &power_amber; |
}; |
|
chosen { |
bootargs = "rootfstype=squashfs noinitrd"; |
stdout-path = "serial0:115200n8"; |
}; |
|
soc { |
pinmux@800000 { |
button_pins: button_pins { |
mux { |
pins = "gpio6", "gpio54", "gpio65"; |
function = "gpio"; |
drive-strength = <2>; |
bias-pull-up; |
}; |
}; |
|
i2c4_pins: i2c4_pinmux { |
mux { |
pins = "gpio12", "gpio13"; |
function = "gsbi4"; |
drive-strength = <12>; |
bias-disable; |
}; |
}; |
|
led_pins: led_pins { |
mux { |
pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", |
"gpio24","gpio26", "gpio53", "gpio64"; |
function = "gpio"; |
drive-strength = <2>; |
bias-pull-up; |
}; |
}; |
|
mdio0_pins: mdio0_pins { |
mux { |
pins = "gpio0", "gpio1"; |
function = "gpio"; |
drive-strength = <8>; |
bias-disable; |
}; |
}; |
|
nand_pins: nand_pins { |
mux { |
pins = "gpio34", "gpio35", "gpio36", |
"gpio37", "gpio38", "gpio39", |
"gpio40", "gpio41", "gpio42", |
"gpio43", "gpio44", "gpio45", |
"gpio46", "gpio47"; |
function = "nand"; |
drive-strength = <10>; |
bias-disable; |
}; |
pullups { |
pins = "gpio39"; |
bias-pull-up; |
}; |
hold { |
pins = "gpio40", "gpio41", "gpio42", |
"gpio43", "gpio44", "gpio45", |
"gpio46", "gpio47"; |
bias-bus-hold; |
}; |
}; |
|
rgmii2_pins: rgmii2_pins { |
mux { |
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", |
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; |
function = "rgmii2"; |
drive-strength = <8>; |
bias-disable; |
}; |
}; |
}; |
|
gsbi@16300000 { |
qcom,mode = <GSBI_PROT_I2C_UART>; |
status = "ok"; |
serial@16340000 { |
status = "ok"; |
}; |
/* |
* The i2c device on gsbi4 should not be enabled. |
* On ipq806x designs gsbi4 i2c is meant for exclusive |
* RPM usage. Turning this on in kernel manifests as |
* i2c failure for the RPM. |
*/ |
}; |
|
sata-phy@1b400000 { |
status = "ok"; |
}; |
|
sata@29000000 { |
status = "ok"; |
}; |
|
phy@100f8800 { /* USB3 port 1 HS phy */ |
clocks = <&gcc USB30_0_UTMI_CLK>; |
status = "ok"; |
}; |
|
phy@100f8830 { /* USB3 port 1 SS phy */ |
clocks = <&gcc USB30_0_MASTER_CLK>; |
status = "ok"; |
}; |
|
phy@110f8800 { /* USB3 port 0 HS phy */ |
clocks = <&gcc USB30_1_UTMI_CLK>; |
status = "ok"; |
}; |
|
phy@110f8830 { /* USB3 port 0 SS phy */ |
clocks = <&gcc USB30_1_MASTER_CLK>; |
status = "ok"; |
}; |
|
usb30@0 { |
clocks = <&gcc USB30_1_MASTER_CLK>; |
status = "ok"; |
}; |
|
usb30@1 { |
clocks = <&gcc USB30_0_MASTER_CLK>; |
status = "ok"; |
}; |
|
pcie0: pci@1b500000 { |
status = "ok"; |
}; |
|
pcie1: pci@1b700000 { |
status = "ok"; |
force_gen1 = <1>; |
}; |
|
nand@1ac00000 { |
status = "ok"; |
|
pinctrl-0 = <&nand_pins>; |
pinctrl-names = "default"; |
|
cs0 { |
reg = <0>; |
compatible = "qcom,nandcs"; |
|
nand-ecc-strength = <4>; |
nand-bus-width = <8>; |
nand-ecc-step-size = <512>; |
|
partitions { |
compatible = "fixed-partitions"; |
#address-cells = <1>; |
#size-cells = <1>; |
|
qcadata@0 { |
label = "qcadata"; |
reg = <0x0000000 0x0c80000>; |
read-only; |
}; |
|
APPSBL@c80000 { |
label = "APPSBL"; |
reg = <0x0c80000 0x0500000>; |
read-only; |
}; |
|
APPSBLENV@1180000 { |
label = "APPSBLENV"; |
reg = <0x1180000 0x0080000>; |
read-only; |
}; |
|
art: art@1200000 { |
label = "art"; |
reg = <0x1200000 0x0140000>; |
read-only; |
}; |
|
kernel@1340000 { |
label = "kernel"; |
reg = <0x1340000 0x0400000>; |
}; |
|
ubi@1740000 { |
label = "ubi"; |
reg = <0x1740000 0x1600000>; |
}; |
|
netgear@2d40000 { |
label = "netgear"; |
reg = <0x2d40000 0x0c00000>; |
read-only; |
}; |
|
reserve@3940000 { |
label = "reserve"; |
reg = <0x3940000 0x46c0000>; |
read-only; |
}; |
}; |
}; |
}; |
|
mdio0: mdio { |
compatible = "virtual,mdio-gpio"; |
#address-cells = <1>; |
#size-cells = <0>; |
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; |
pinctrl-0 = <&mdio0_pins>; |
pinctrl-names = "default"; |
|
phy0: ethernet-phy@0 { |
reg = <0>; |
qca,ar8327-initvals = < |
0x00004 0x7600000 /* PAD0_MODE */ |
0x00008 0x1000000 /* PAD5_MODE */ |
0x0000c 0x80 /* PAD6_MODE */ |
0x000e4 0x6a545 /* MAC_POWER_SEL */ |
0x000e0 0xc74164de /* SGMII_CTRL */ |
0x0007c 0x4e /* PORT0_STATUS */ |
0x00094 0x4e /* PORT6_STATUS */ |
>; |
}; |
|
phy4: ethernet-phy@4 { |
reg = <4>; |
}; |
}; |
|
gmac1: ethernet@37200000 { |
status = "ok"; |
phy-mode = "rgmii"; |
qcom,id = <1>; |
|
pinctrl-0 = <&rgmii2_pins>; |
pinctrl-names = "default"; |
|
mtd-mac-address = <&art 6>; |
|
fixed-link { |
speed = <1000>; |
full-duplex; |
}; |
}; |
|
gmac2: ethernet@37400000 { |
status = "ok"; |
phy-mode = "sgmii"; |
qcom,id = <2>; |
|
mtd-mac-address = <&art 0>; |
|
fixed-link { |
speed = <1000>; |
full-duplex; |
}; |
}; |
}; |
|
keys { |
compatible = "gpio-keys"; |
pinctrl-0 = <&button_pins>; |
pinctrl-names = "default"; |
|
wifi { |
label = "wifi"; |
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RFKILL>; |
}; |
|
reset { |
label = "reset"; |
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RESTART>; |
}; |
|
wps { |
label = "wps"; |
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_WPS_BUTTON>; |
}; |
}; |
|
leds { |
compatible = "gpio-leds"; |
pinctrl-0 = <&led_pins>; |
pinctrl-names = "default"; |
|
usb1 { |
label = "r7500:white:usb1"; |
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; |
}; |
|
usb2 { |
label = "r7500:white:usb2"; |
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; |
}; |
|
power_amber: power_amber { |
label = "r7500:amber:power"; |
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; |
}; |
|
wan_white { |
label = "r7500:white:wan"; |
gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; |
}; |
|
wan_amber { |
label = "r7500:amber:wan"; |
gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; |
}; |
|
wps { |
label = "r7500:white:wps"; |
gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; |
}; |
|
esata { |
label = "r7500:white:esata"; |
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; |
}; |
|
power_white: power_white { |
label = "r7500:white:power"; |
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; |
default-state = "keep"; |
}; |
|
wifi { |
label = "r7500:white:wifi"; |
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; |
}; |
}; |
}; |
|
&tcsr { |
qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>; |
compatible = "qcom,tcsr"; |
}; |
|
&adm_dma { |
status = "ok"; |
}; |