OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3883.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "omnima,hpm", "ralink,rt3883-soc"; |
||
10 | model = "Omnima HPM"; |
||
11 | |||
12 | aliases { |
||
13 | led-boot = &led_status; |
||
14 | led-failsafe = &led_status; |
||
15 | led-running = &led_status; |
||
16 | led-upgrade = &led_status; |
||
17 | }; |
||
18 | |||
19 | chosen { |
||
20 | bootargs = "console=ttyS0,115200"; |
||
21 | }; |
||
22 | |||
23 | keys { |
||
24 | compatible = "gpio-keys-polled"; |
||
25 | poll-interval = <100>; |
||
26 | |||
27 | reset { |
||
28 | label = "reset"; |
||
29 | gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; |
||
30 | linux,code = <KEY_RESTART>; |
||
31 | }; |
||
32 | }; |
||
33 | |||
34 | leds { |
||
35 | compatible = "gpio-leds"; |
||
36 | |||
37 | power { |
||
38 | label = "hpm:orange:power"; |
||
39 | gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; |
||
40 | default-state = "on"; |
||
41 | }; |
||
42 | |||
43 | led_status: status { |
||
44 | label = "hpm:green:status"; |
||
45 | gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; |
||
46 | default-state = "on"; |
||
47 | }; |
||
48 | |||
49 | eth { |
||
50 | label = "hpm:green:eth"; |
||
51 | gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; |
||
52 | }; |
||
53 | |||
54 | eth2 { |
||
55 | label = "hpm:red:eth"; |
||
56 | gpios = <&gpio0 18 GPIO_ACTIVE_LOW>; |
||
57 | }; |
||
58 | |||
59 | wifi { |
||
60 | label = "hpm:green:wifi"; |
||
61 | gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; |
||
62 | }; |
||
63 | |||
64 | wifi2 { |
||
65 | label = "hpm:red:wifi"; |
||
66 | gpios = <&gpio0 19 GPIO_ACTIVE_LOW>; |
||
67 | }; |
||
68 | }; |
||
69 | |||
70 | gpio_export { |
||
71 | compatible = "gpio-export"; |
||
72 | #size-cells = <0>; |
||
73 | /* gpio 12 and 13 handle the OC input */ |
||
74 | |||
75 | usb0 { |
||
76 | gpio-export,name = "usb0"; |
||
77 | gpio-export,output = <1>; |
||
78 | gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
||
79 | }; |
||
80 | |||
81 | usb1 { |
||
82 | gpio-export,name = "usb1"; |
||
83 | gpio-export,output = <1>; |
||
84 | gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; |
||
85 | }; |
||
86 | }; |
||
87 | }; |
||
88 | |||
89 | &spi0 { |
||
90 | status = "okay"; |
||
91 | |||
92 | m25p80@0 { |
||
93 | compatible = "jedec,spi-nor"; |
||
94 | spi-max-frequency = <25000000>; |
||
95 | reg = <0>; |
||
96 | |||
97 | partitions { |
||
98 | compatible = "fixed-partitions"; |
||
99 | #address-cells = <1>; |
||
100 | #size-cells = <1>; |
||
101 | |||
102 | partition@0 { |
||
103 | reg = <0x0 0x0030000>; |
||
104 | label = "u-boot"; |
||
105 | read-only; |
||
106 | }; |
||
107 | |||
108 | partition@30000 { |
||
109 | reg = <0x00030000 0x00010000>; |
||
110 | label = "config"; |
||
111 | read-only; |
||
112 | }; |
||
113 | |||
114 | factory: partition@40000 { |
||
115 | reg = <0x00040000 0x00010000>; |
||
116 | label = "factory"; |
||
117 | read-only; |
||
118 | }; |
||
119 | |||
120 | partition@50000 { |
||
121 | compatible = "denx,uimage"; |
||
122 | reg = <0x00050000 0x00fb0000>; |
||
123 | label = "firmware"; |
||
124 | }; |
||
125 | }; |
||
126 | }; |
||
127 | }; |
||
128 | |||
129 | &pinctrl { |
||
130 | state_default: pinctrl0 { |
||
131 | gpio { |
||
132 | ralink,group = "i2c", "jtag", "uartf"; |
||
133 | ralink,function = "gpio"; |
||
134 | }; |
||
135 | }; |
||
136 | }; |
||
137 | |||
138 | ðernet { |
||
139 | phy-handle = <&phy0>; |
||
140 | phy-mode = "rgmii"; |
||
141 | mtd-mac-address = <&factory 0x28>; |
||
142 | |||
143 | mdio-bus { |
||
144 | status = "okay"; |
||
145 | |||
146 | phy0: ethernet-phy@4 { |
||
147 | reg = <4>; |
||
148 | }; |
||
149 | }; |
||
150 | }; |
||
151 | |||
152 | &wmac { |
||
153 | ralink,mtd-eeprom = <&factory 0>; |
||
154 | }; |
||
155 | |||
156 | &ehci { |
||
157 | status = "okay"; |
||
158 | }; |
||
159 | |||
160 | &ohci { |
||
161 | status = "okay"; |
||
162 | }; |