OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "ar9.dtsi" |
||
4 | |||
5 | #include <dt-bindings/input/input.h> |
||
6 | |||
7 | / { |
||
8 | compatible = "avm,fritz7320", "lantiq,xway", "lantiq,ar9"; |
||
9 | model = "AVM FRITZ!Box 7320"; |
||
10 | |||
11 | chosen { |
||
12 | bootargs = "console=ttyLTQ0,115200"; |
||
13 | }; |
||
14 | |||
15 | aliases { |
||
16 | led-boot = &power; |
||
17 | led-failsafe = &power; |
||
18 | led-running = &power; |
||
19 | led-upgrade = &power; |
||
20 | |||
21 | led-internet = &info_green; |
||
22 | led-dsl = &power; |
||
23 | led-wifi = &wlan; |
||
24 | }; |
||
25 | |||
26 | memory@0 { |
||
27 | reg = <0x0 0x4000000>; |
||
28 | }; |
||
29 | |||
30 | gpio-keys-polled { |
||
31 | compatible = "gpio-keys-polled"; |
||
32 | #address-cells = <1>; |
||
33 | #size-cells = <0>; |
||
34 | poll-interval = <100>; |
||
35 | |||
36 | rfkill { |
||
37 | label = "rfkill"; |
||
38 | gpios = <&gpio 1 GPIO_ACTIVE_LOW>; |
||
39 | linux,code = <KEY_RFKILL>; |
||
40 | }; |
||
41 | dect { |
||
42 | label = "dect"; |
||
43 | gpios = <&gpio 2 GPIO_ACTIVE_LOW>; |
||
44 | linux,code = <KEY_PHONE>; |
||
45 | }; |
||
46 | }; |
||
47 | |||
48 | gpio-leds { |
||
49 | compatible = "gpio-leds"; |
||
50 | power: power { |
||
51 | label = "fritz7320:green:power"; |
||
52 | gpios = <&gpio 44 GPIO_ACTIVE_LOW>; |
||
53 | default-state = "keep"; |
||
54 | }; |
||
55 | voice { |
||
56 | label = "fritz7320:green:fon"; |
||
57 | gpios = <&gpio 47 GPIO_ACTIVE_LOW>; |
||
58 | }; |
||
59 | dect { |
||
60 | label = "fritz7320:green:dect"; |
||
61 | gpios = <&gpio 38 GPIO_ACTIVE_LOW>; |
||
62 | }; |
||
63 | wlan: wlan { |
||
64 | label = "fritz7320:green:wlan"; |
||
65 | gpios = <&gpio 37 GPIO_ACTIVE_LOW>; |
||
66 | }; |
||
67 | info_green: info_green { |
||
68 | label = "fritz7320:green:info"; |
||
69 | gpios = <&gpio 35 GPIO_ACTIVE_LOW>; |
||
70 | }; |
||
71 | info_red { |
||
72 | label = "fritz7320:red:info"; |
||
73 | gpios = <&gpio 45 GPIO_ACTIVE_LOW>; |
||
74 | }; |
||
75 | }; |
||
76 | }; |
||
77 | |||
78 | &gpio { |
||
79 | pinctrl-names = "default"; |
||
80 | pinctrl-0 = <&state_default>; |
||
81 | |||
82 | state_default: pinmux { |
||
83 | pci { |
||
84 | lantiq,groups = "gnt1", "req1", "req2", "req3", "req4", "gnt2", "gnt3", "gnt4"; |
||
85 | lantiq,function = "pci"; |
||
86 | }; |
||
87 | pci-in { |
||
88 | lantiq,groups = "req1", "req2", "req3", "req4"; |
||
89 | lantiq,output = <0>; |
||
90 | lantiq,open-drain = <1>; |
||
91 | lantiq,pull = <2>; |
||
92 | }; |
||
93 | pci-out { |
||
94 | lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4"; |
||
95 | lantiq,output = <1>; |
||
96 | lantiq,pull = <0>; |
||
97 | }; |
||
98 | }; |
||
99 | }; |
||
100 | |||
101 | &gsw { |
||
102 | phy-mode = "mii"; |
||
103 | mtd-mac-address = <&ath9k_cal 0xa91>; |
||
104 | mtd-mac-address-increment = <(-2)>; |
||
105 | }; |
||
106 | |||
107 | &localbus { |
||
108 | nor@0 { |
||
109 | compatible = "lantiq,nor"; |
||
110 | bank-width = <2>; |
||
111 | reg = <0 0x0 0x1000000>; |
||
112 | #address-cells = <1>; |
||
113 | #size-cells = <1>; |
||
114 | |||
115 | partitions { |
||
116 | compatible = "fixed-partitions"; |
||
117 | #address-cells = <1>; |
||
118 | #size-cells = <1>; |
||
119 | |||
120 | ath9k_cal: partition@0 { |
||
121 | label = "urlader"; |
||
122 | reg = <0x00000 0x20000>; |
||
123 | read-only; |
||
124 | }; |
||
125 | |||
126 | partition@20000 { |
||
127 | label = "firmware"; |
||
128 | reg = <0x20000 0xf60000>; |
||
129 | }; |
||
130 | |||
131 | partition@f80000 { |
||
132 | label = "tffs (1)"; |
||
133 | reg = <0xf80000 0x40000>; |
||
134 | read-only; |
||
135 | }; |
||
136 | |||
137 | partition@fc0000 { |
||
138 | label = "tffs (2)"; |
||
139 | reg = <0xfc0000 0x40000>; |
||
140 | read-only; |
||
141 | }; |
||
142 | }; |
||
143 | }; |
||
144 | }; |
||
145 | |||
146 | &pci0 { |
||
147 | status = "okay"; |
||
148 | req-mask = <0xf>; |
||
149 | gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; |
||
150 | |||
151 | wifi@0,0 { |
||
152 | compatible = "pci0,0"; |
||
153 | reg = <0x7000 0 0 0 0>; |
||
154 | qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ |
||
155 | }; |
||
156 | }; |
||
157 | |||
158 | &usb_phy0 { |
||
159 | status = "okay"; |
||
160 | }; |
||
161 | |||
162 | &usb_phy1 { |
||
163 | status = "okay"; |
||
164 | }; |
||
165 | |||
166 | &usb0 { |
||
167 | status = "okay"; |
||
168 | }; |
||
169 | |||
170 | &usb1 { |
||
171 | status = "okay"; |
||
172 | }; |