OpenWrt – Blame information for rev 1

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "ar9331.dtsi"
8  
9 / {
10 aliases {
11 serial0 = &uart;
12 led-boot = &system;
13 led-failsafe = &system;
14 led-running = &system;
15 led-upgrade = &system;
16 };
17  
18 keys {
19 compatible = "gpio-keys-polled";
20 poll-interval = <20>;
21  
22 reset {
23 label = "reset";
24 linux,code = <KEY_RESTART>;
25 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
26 debounce-interval = <60>;
27 };
28 };
29  
30 leds {
31 compatible = "gpio-leds";
32  
33 system: system {
34 label = "tl-wr703n:blue:system";
35 gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
36 };
37 };
38  
39 reg_usb_vbus: reg_usb_vbus {
40 compatible = "regulator-fixed";
41 regulator-name = "usb_vbus";
42 regulator-min-microvolt = <5000000>;
43 regulator-max-microvolt = <5000000>;
44 enable-active-high;
45 };
46  
47 };
48  
49 &spi {
50 status = "okay";
51 num-cs = <1>;
52  
53 flash@0 {
54 compatible = "jedec,spi-nor";
55 reg = <0>;
56 spi-max-frequency = <25000000>;
57  
58 partitions {
59 compatible = "fixed-partitions";
60 #address-cells = <1>;
61 #size-cells = <1>;
62  
63 uboot: partition@0 {
64 reg = <0x0 0x20000>;
65 label = "u-boot";
66 read-only;
67 };
68  
69 firmware: partition@20000 {
70 compatible = "tplink,firmware";
71 reg = <0x20000 0x3d0000>;
72 label = "firmware";
73 };
74  
75 art: partition@3f0000 {
76 reg = <0x3f0000 0x10000>;
77 label = "art";
78 read-only;
79 };
80 };
81 };
82 };
83  
84 &eth0 {
85 status = "okay";
86  
87 mtd-mac-address = <&uboot 0x1fc00>;
88  
89 gmac-config {
90 device = <&gmac>;
91  
92 switch-phy-addr-swap = <0>;
93 switch-phy-swap = <0>;
94 };
95 };
96  
97 &eth1 {
98 status = "okay";
99 compatible = "syscon", "simple-mfd";
100 };
101  
102 &gpio {
103 status = "okay";
104 };
105  
106 &uart {
107 status = "okay";
108 };
109  
110 &usb {
111 dr_mode = "host";
112 vbus-supply = <&reg_usb_vbus>;
113 status = "okay";
114 };
115  
116 &usb_phy {
117 status = "okay";
118 };
119  
120 &wmac {
121 status = "okay";
122 mtd-cal-data = <&art 0x1000>;
123 mtd-mac-address = <&uboot 0x1fc00>;
124 };