OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | // SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
2 | /dts-v1/; |
||
3 | |||
4 | #include <dt-bindings/gpio/gpio.h> |
||
5 | #include <dt-bindings/input/input.h> |
||
6 | |||
7 | #include "ar9330.dtsi" |
||
8 | |||
9 | / { |
||
10 | model = "GL.iNet GL-AR150"; |
||
11 | compatible = "glinet,gl-ar150", "qca,ar9330"; |
||
12 | |||
13 | aliases { |
||
14 | serial0 = &uart; |
||
15 | led-boot = &wlan; |
||
16 | led-failsafe = &wlan; |
||
17 | led-upgrade = &wlan; |
||
18 | }; |
||
19 | |||
20 | leds { |
||
21 | compatible = "gpio-leds"; |
||
22 | |||
23 | wlan: wlan { |
||
24 | label = "gl-ar150:orange:wlan"; |
||
25 | gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; |
||
26 | linux,default-trigger = "phy0tpt"; |
||
27 | }; |
||
28 | |||
29 | lan { |
||
30 | label = "gl-ar150:green:lan"; |
||
31 | gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; |
||
32 | }; |
||
33 | |||
34 | wan { |
||
35 | label = "gl-ar150:green:wan"; |
||
36 | gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; |
||
37 | }; |
||
38 | }; |
||
39 | |||
40 | keys { |
||
41 | compatible = "gpio-keys-polled"; |
||
42 | poll-interval = <100>; |
||
43 | |||
44 | manual { |
||
45 | label = "manual"; |
||
46 | linux,code = <BTN_7>; |
||
47 | gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; |
||
48 | }; |
||
49 | |||
50 | auto { |
||
51 | label = "auto"; |
||
52 | linux,code = <BTN_8>; |
||
53 | gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; |
||
54 | }; |
||
55 | |||
56 | reset { |
||
57 | label = "reset"; |
||
58 | linux,code = <KEY_RESTART>; |
||
59 | gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; |
||
60 | }; |
||
61 | }; |
||
62 | }; |
||
63 | |||
64 | &uart { |
||
65 | status = "okay"; |
||
66 | }; |
||
67 | |||
68 | &gpio { |
||
69 | status = "okay"; |
||
70 | }; |
||
71 | |||
72 | &usb { |
||
73 | dr_mode = "host"; |
||
74 | status = "okay"; |
||
75 | }; |
||
76 | |||
77 | &usb_phy { |
||
78 | status = "okay"; |
||
79 | gpios = <&gpio 6 GPIO_ACTIVE_HIGH>; |
||
80 | }; |
||
81 | |||
82 | &spi { |
||
83 | num-chipselects = <1>; |
||
84 | status = "okay"; |
||
85 | |||
86 | flash@0 { |
||
87 | compatible = "jedec,spi-nor"; |
||
88 | spi-max-frequency = <104000000>; |
||
89 | reg = <0>; |
||
90 | |||
91 | partitions { |
||
92 | compatible = "fixed-partitions"; |
||
93 | #address-cells = <1>; |
||
94 | #size-cells = <1>; |
||
95 | |||
96 | partition@0 { |
||
97 | label = "u-boot"; |
||
98 | reg = <0x000000 0x040000>; |
||
99 | read-only; |
||
100 | }; |
||
101 | |||
102 | partition@1 { |
||
103 | label = "u-boot-env"; |
||
104 | reg = <0x040000 0x010000>; |
||
105 | }; |
||
106 | |||
107 | partition@2 { |
||
108 | compatible = "denx,uimage"; |
||
109 | label = "firmware"; |
||
110 | reg = <0x050000 0xfa0000>; |
||
111 | }; |
||
112 | |||
113 | art: partition@3 { |
||
114 | label = "ART"; |
||
115 | reg = <0xff0000 0x010000>; |
||
116 | read-only; |
||
117 | }; |
||
118 | }; |
||
119 | }; |
||
120 | }; |
||
121 | |||
122 | ð0 { |
||
123 | status = "okay"; |
||
124 | |||
125 | mtd-mac-address = <&art 0x0>; |
||
126 | }; |
||
127 | |||
128 | ð1 { |
||
129 | status = "okay"; |
||
130 | |||
131 | mtd-mac-address = <&art 0x0>; |
||
132 | |||
133 | gmac-config { |
||
134 | device = <&gmac>; |
||
135 | |||
136 | switch-phy-addr-swap = <0>; |
||
137 | switch-phy-swap = <0>; |
||
138 | }; |
||
139 | }; |
||
140 | |||
141 | &wmac { |
||
142 | status = "okay"; |
||
143 | mtd-cal-data = <&art 0x1000>; |
||
144 | mtd-mac-address = <&art 0x0>; |
||
145 | }; |