OpenWrt – Blame information for rev 4
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
4 | office | 1 | --- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c |
2 | +++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c |
||
3 | @@ -3,6 +3,7 @@ |
||
4 | * |
||
5 | * Board setup for the Linksys WRT300N v2 |
||
6 | * |
||
7 | + * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com> |
||
8 | * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org> |
||
9 | * |
||
10 | * based on coyote-setup.c: |
||
11 | @@ -18,6 +19,7 @@ |
||
12 | #include <linux/tty.h> |
||
13 | #include <linux/serial_8250.h> |
||
14 | #include <linux/slab.h> |
||
15 | +#include <linux/etherdevice.h> |
||
16 | |||
17 | #include <asm/types.h> |
||
18 | #include <asm/setup.h> |
||
19 | @@ -79,7 +81,8 @@ static struct platform_device wrt300nv2_ |
||
20 | /* Built-in 10/100 Ethernet MAC interfaces */ |
||
21 | static struct eth_plat_info wrt300nv2_plat_eth[] = { |
||
22 | { |
||
23 | - .phy = -1, |
||
24 | + .phy = IXP4XX_ETH_PHY_MAX_ADDR, |
||
25 | + .phy_mask = 0x0F0000, |
||
26 | .rxq = 3, |
||
27 | .txreadyq = 20, |
||
28 | }, { |
||
29 | @@ -112,6 +115,10 @@ static struct platform_device *wrt300nv2 |
||
30 | |||
31 | static void __init wrt300nv2_init(void) |
||
32 | { |
||
33 | + uint8_t __iomem *f; |
||
34 | + int offset = 0; |
||
35 | + int i; |
||
36 | + |
||
37 | ixp4xx_sys_init(); |
||
38 | |||
39 | wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); |
||
40 | @@ -121,6 +128,32 @@ static void __init wrt300nv2_init(void) |
||
41 | *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; |
||
42 | |||
43 | platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices)); |
||
44 | + |
||
45 | + f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x60000); |
||
46 | + |
||
47 | + if (f) { |
||
48 | + for (i = 0; i < 6; i++) { |
||
49 | +#ifdef __ARMEB__ |
||
50 | + wrt300nv2_plat_eth[0].hwaddr[i] = readb(f + 0x5FFA0 + i); |
||
51 | + if (i == 5) |
||
52 | + offset = 1; |
||
53 | + wrt300nv2_plat_eth[1].hwaddr[i] = (wrt300nv2_plat_eth[0].hwaddr[i] + offset); |
||
54 | +#else |
||
55 | + wrt300nv2_plat_eth[0].hwaddr[i] = readb(f + 0x5FFA0 + (i^3)); |
||
56 | + if (i == 5) |
||
57 | + offset = 1; |
||
58 | + wrt300nv2_plat_eth[1].hwaddr[i] = (wrt300nv2_plat_eth[0].hwaddr[i] + offset); |
||
59 | +#endif |
||
60 | + } |
||
61 | + iounmap(f); |
||
62 | + } |
||
63 | + |
||
64 | + if (!(is_valid_ether_addr(wrt300nv2_plat_eth[0].hwaddr))) |
||
65 | + random_ether_addr(wrt300nv2_plat_eth[0].hwaddr); |
||
66 | + if (!(is_valid_ether_addr(wrt300nv2_plat_eth[1].hwaddr))) { |
||
67 | + memcpy(wrt300nv2_plat_eth[1].hwaddr, wrt300nv2_plat_eth[0].hwaddr, ETH_ALEN); |
||
68 | + wrt300nv2_plat_eth[1].hwaddr[5] = (wrt300nv2_plat_eth[0].hwaddr[5] + 1); |
||
69 | + } |
||
70 | } |
||
71 | |||
72 | #ifdef CONFIG_MACH_WRT300NV2 |