OpenWrt – Blame information for rev 3

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 /dts-v1/;
2  
3 #include "rt2880.dtsi"
4  
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/input.h>
7  
8 / {
9 #address-cells = <1>;
10 #size-cells = <1>;
11 compatible = "asus,rt-n15", "ralink,rt2880-soc";
12 model = "Asus RT-N15";
13  
14 cfi@1f000000 {
15 compatible = "cfi-flash";
16 reg = <0x1f000000 0x800000>;
17 bank-width = <2>;
18 device-width = <2>;
3 office 19 #address-cells = <1>;
20 #size-cells = <1>;
1 office 21  
3 office 22 partition@0 {
23 label = "uboot";
24 reg = <0x0 0x30000>;
25 read-only;
26 };
1 office 27  
3 office 28 partition@30000 {
29 label = "uboot-env";
30 reg = <0x30000 0x10000>;
31 read-only;
32 };
1 office 33  
3 office 34 factory: partition@40000 {
35 label = "factory";
36 reg = <0x40000 0x10000>;
37 read-only;
38 };
1 office 39  
3 office 40 partition@50000 {
41 label = "firmware";
42 reg = <0x50000 0x3b0000>;
1 office 43 };
44 };
45  
46 rtl8366s {
47 compatible = "realtek,rtl8366s";
48 gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
49 gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
50 };
51  
3 office 52 gpio-keys-polled {
1 office 53 compatible = "gpio-keys-polled";
3 office 54 #address-cells = <1>;
55 #size-cells = <0>;
1 office 56 poll-interval = <100>;
57  
58 wps {
59 label = "wps";
60 gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
61 linux,code = <KEY_WPS_BUTTON>;
62 };
63  
64 reset {
65 label = "reset";
66 gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
67 linux,code = <KEY_RESTART>;
68 };
69 };
70  
3 office 71 gpio-leds {
1 office 72 compatible = "gpio-leds";
73  
3 office 74 power {
1 office 75 label = "rt-n15:blue:power";
76 gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
77 };
78 };
79 };
80  
81 &gpio0 {
82 status = "okay";
83 };
84  
85 &pinctrl {
86 state_default: pinctrl0 {
87 gpio {
88 ralink,group = "i2c", "uartlite", "mdio";
89 ralink,function = "gpio";
90 };
91 };
92 };
93  
94 &ethernet {
95 status = "okay";
96 mtd-mac-address = <&factory 0x4>;
97  
98 port@0 {
99 mediatek,fixed-link = <1000 1 1 1>;
100 };
101  
102 mdio-bus {
103 status = "okay";
104  
105 phy0: ethernet-phy@0 {
106 phy-mode = "mii";
107 reg = <0>;
108 };
109 };
110 };
111  
112 &wmac {
113 ralink,mtd-eeprom = <&factory 0>;
114 };