OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "mt7620a.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "phicomm,psg1208", "ralink,mt7620a-soc"; |
||
10 | model = "Phicomm PSG1208"; |
||
11 | |||
3 | office | 12 | gpio-leds { |
1 | office | 13 | compatible = "gpio-leds"; |
14 | |||
3 | office | 15 | wan { |
1 | office | 16 | label = "psg1208:white:wps"; |
17 | gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; |
||
18 | }; |
||
19 | |||
20 | wlan { |
||
21 | label = "psg1208:white:wlan2g"; |
||
22 | gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; |
||
23 | }; |
||
24 | }; |
||
25 | |||
3 | office | 26 | gpio-keys-polled { |
1 | office | 27 | compatible = "gpio-keys-polled"; |
3 | office | 28 | #address-cells = <1>; |
29 | #size-cells = <0>; |
||
1 | office | 30 | poll-interval = <20>; |
31 | |||
32 | reset { |
||
33 | label = "reset"; |
||
34 | gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
||
35 | linux,code = <KEY_RESTART>; |
||
36 | }; |
||
37 | }; |
||
38 | }; |
||
39 | |||
40 | &gpio1 { |
||
41 | status = "okay"; |
||
42 | }; |
||
43 | |||
44 | &gpio3 { |
||
45 | status = "okay"; |
||
46 | }; |
||
47 | |||
48 | &spi0 { |
||
49 | status = "okay"; |
||
50 | |||
51 | m25p80@0 { |
||
3 | office | 52 | #address-cells = <1>; |
53 | #size-cells = <1>; |
||
1 | office | 54 | compatible = "jedec,spi-nor"; |
55 | reg = <0>; |
||
56 | spi-max-frequency = <10000000>; |
||
57 | |||
3 | office | 58 | partition@0 { |
59 | label = "u-boot"; |
||
60 | reg = <0x0 0x30000>; |
||
61 | read-only; |
||
62 | }; |
||
1 | office | 63 | |
3 | office | 64 | partition@20000 { |
65 | label = "u-boot-env"; |
||
66 | reg = <0x30000 0x10000>; |
||
67 | read-only; |
||
68 | }; |
||
1 | office | 69 | |
3 | office | 70 | factory: partition@30000 { |
71 | label = "factory"; |
||
72 | reg = <0x40000 0x10000>; |
||
73 | read-only; |
||
74 | }; |
||
1 | office | 75 | |
3 | office | 76 | partition@40000 { |
77 | label = "firmware"; |
||
78 | reg = <0x50000 0x7b0000>; |
||
1 | office | 79 | }; |
80 | }; |
||
81 | }; |
||
82 | |||
83 | &pinctrl { |
||
84 | state_default: pinctrl0 { |
||
85 | gpio { |
||
86 | ralink,group = "i2c", "spi refclk", "wled"; |
||
87 | ralink,function = "gpio"; |
||
88 | }; |
||
89 | }; |
||
90 | }; |
||
91 | |||
92 | ðernet { |
||
93 | pinctrl-names = "default"; |
||
94 | pinctrl-0 = <&ephy_pins>; |
||
95 | mtd-mac-address = <&factory 0x4>; |
||
96 | mediatek,portmap = "llllw"; |
||
97 | }; |
||
98 | |||
99 | &pcie { |
||
100 | status = "okay"; |
||
101 | |||
3 | office | 102 | pcie-bridge { |
103 | mt76@0,0 { |
||
104 | reg = <0x0000 0 0 0 0>; |
||
105 | device_type = "pci"; |
||
106 | mediatek,mtd-eeprom = <&factory 0x8000>; |
||
107 | ieee80211-freq-limit = <5000000 6000000>; |
||
108 | }; |
||
1 | office | 109 | }; |
110 | }; |
||
111 | |||
112 | &wmac { |
||
113 | ralink,mtd-eeprom = <&factory 0>; |
||
114 | }; |