OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "mt7620a.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "xiaomi,miwifi-mini", "ralink,mt7620a-soc"; |
||
10 | model = "Xiaomi MiWiFi Mini"; |
||
11 | |||
12 | chosen { |
||
13 | bootargs = "console=ttyS0,115200"; |
||
14 | }; |
||
15 | |||
3 | office | 16 | gpio-leds { |
1 | office | 17 | compatible = "gpio-leds"; |
18 | |||
3 | office | 19 | blue { |
1 | office | 20 | label = "miwifi-mini:blue:status"; |
21 | gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; |
||
22 | }; |
||
23 | |||
24 | yellow { |
||
25 | label = "miwifi-mini:yellow:status"; |
||
26 | gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; |
||
27 | }; |
||
28 | |||
29 | red { |
||
30 | label = "miwifi-mini:red:status"; |
||
31 | gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; |
||
32 | }; |
||
33 | }; |
||
34 | |||
3 | office | 35 | gpio-keys-polled { |
1 | office | 36 | compatible = "gpio-keys-polled"; |
3 | office | 37 | #address-cells = <1>; |
38 | #size-cells = <0>; |
||
1 | office | 39 | poll-interval = <20>; |
40 | |||
41 | reset { |
||
42 | label = "reset"; |
||
43 | gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; |
||
44 | linux,code = <KEY_RESTART>; |
||
45 | }; |
||
46 | }; |
||
47 | }; |
||
48 | |||
49 | &gpio0 { |
||
50 | status = "okay"; |
||
51 | }; |
||
52 | |||
53 | &gpio1 { |
||
54 | status = "okay"; |
||
55 | }; |
||
56 | |||
57 | &gpio2 { |
||
58 | status = "okay"; |
||
59 | }; |
||
60 | |||
61 | &spi0 { |
||
62 | status = "okay"; |
||
63 | |||
64 | m25p80@0 { |
||
3 | office | 65 | #address-cells = <1>; |
66 | #size-cells = <1>; |
||
1 | office | 67 | compatible = "jedec,spi-nor"; |
68 | reg = <0>; |
||
69 | spi-max-frequency = <10000000>; |
||
70 | |||
3 | office | 71 | partition@0 { |
72 | label = "u-boot"; |
||
73 | reg = <0x0 0x30000>; |
||
74 | }; |
||
1 | office | 75 | |
3 | office | 76 | partition@30000 { |
77 | label = "u-boot-env"; |
||
78 | reg = <0x30000 0x10000>; |
||
79 | read-only; |
||
80 | }; |
||
1 | office | 81 | |
3 | office | 82 | factory: partition@40000 { |
83 | label = "factory"; |
||
84 | reg = <0x40000 0x10000>; |
||
85 | read-only; |
||
86 | }; |
||
1 | office | 87 | |
3 | office | 88 | partition@50000 { |
89 | label = "firmware"; |
||
90 | reg = <0x50000 0xf80000>; |
||
91 | }; |
||
1 | office | 92 | |
3 | office | 93 | partition@fd0000 { |
94 | label = "crash"; |
||
95 | reg = <0xfd0000 0x10000>; |
||
96 | }; |
||
1 | office | 97 | |
3 | office | 98 | partition@fe0000 { |
99 | label = "reserved"; |
||
100 | reg = <0xfe0000 0x10000>; |
||
101 | read-only; |
||
102 | }; |
||
1 | office | 103 | |
3 | office | 104 | partition@ff0000 { |
105 | label = "Bdata"; |
||
106 | reg = <0xff0000 0x10000>; |
||
1 | office | 107 | }; |
108 | }; |
||
109 | }; |
||
110 | |||
111 | &ehci { |
||
112 | status = "okay"; |
||
113 | }; |
||
114 | |||
115 | &ohci { |
||
116 | status = "okay"; |
||
117 | }; |
||
118 | |||
119 | ðernet { |
||
120 | pinctrl-names = "default"; |
||
121 | pinctrl-0 = <&ephy_pins>; |
||
122 | mtd-mac-address = <&factory 0x28>; |
||
123 | mediatek,portmap = "llllw"; |
||
124 | }; |
||
125 | |||
126 | &wmac { |
||
127 | ralink,mtd-eeprom = <&factory 0>; |
||
128 | pinctrl-names = "default"; |
||
129 | pinctrl-0 = <&pa_pins>; |
||
130 | }; |
||
131 | |||
132 | &pcie { |
||
133 | status = "okay"; |
||
134 | |||
3 | office | 135 | pcie-bridge { |
136 | mt76@0,0 { |
||
137 | reg = <0x0000 0 0 0 0>; |
||
138 | device_type = "pci"; |
||
139 | mediatek,mtd-eeprom = <&factory 0x8000>; |
||
140 | ieee80211-freq-limit = <5000000 6000000>; |
||
141 | }; |
||
1 | office | 142 | }; |
143 | }; |
||
144 | |||
145 | &pinctrl { |
||
146 | state_default: pinctrl0 { |
||
147 | gpio { |
||
148 | ralink,group = "i2c", "rgmii1"; |
||
149 | ralink,function = "gpio"; |
||
150 | }; |
||
151 | }; |
||
152 | }; |