OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt2880.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | #address-cells = <1>; |
||
10 | #size-cells = <1>; |
||
11 | compatible = "buffalo,wli-tx4-ag300n", "ralink,rt2880-soc"; |
||
12 | model = "Buffalo WLI-TX4-AG300N"; |
||
13 | |||
14 | aliases { |
||
15 | led-boot = &led_power; |
||
16 | led-failsafe = &led_power; |
||
17 | led-running = &led_power; |
||
18 | led-upgrade = &led_power; |
||
19 | }; |
||
20 | |||
21 | cfi@1f000000 { |
||
22 | compatible = "cfi-flash"; |
||
23 | reg = <0x1f000000 0x800000>; |
||
24 | bank-width = <2>; |
||
25 | device-width = <2>; |
||
26 | |||
27 | partitions { |
||
28 | compatible = "fixed-partitions"; |
||
29 | #address-cells = <1>; |
||
30 | #size-cells = <1>; |
||
31 | |||
32 | partition@0 { |
||
33 | label = "uboot"; |
||
34 | reg = <0x0 0x30000>; |
||
35 | read-only; |
||
36 | }; |
||
37 | |||
38 | partition@30000 { |
||
39 | label = "uboot-env"; |
||
40 | reg = <0x30000 0x10000>; |
||
41 | read-only; |
||
42 | }; |
||
43 | |||
44 | factory: partition@40000 { |
||
45 | label = "factory"; |
||
46 | reg = <0x40000 0x10000>; |
||
47 | read-only; |
||
48 | }; |
||
49 | |||
50 | partition@50000 { |
||
51 | compatible = "denx,uimage"; |
||
52 | label = "firmware"; |
||
53 | reg = <0x50000 0x3b0000>; |
||
54 | }; |
||
55 | }; |
||
56 | }; |
||
57 | |||
58 | keys { |
||
59 | compatible = "gpio-keys-polled"; |
||
60 | poll-interval = <100>; |
||
61 | |||
62 | wps { |
||
63 | label = "wps"; |
||
64 | gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
||
65 | linux,code = <KEY_WPS_BUTTON>; |
||
66 | }; |
||
67 | |||
68 | bandwidth { |
||
69 | label = "bandwidth"; |
||
70 | gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; |
||
71 | linux,code = <KEY_RESTART>; |
||
72 | }; |
||
73 | |||
74 | reset { |
||
75 | label = "reset"; |
||
76 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
77 | linux,code = <KEY_RESTART>; |
||
78 | }; |
||
79 | }; |
||
80 | |||
81 | leds { |
||
82 | compatible = "gpio-leds"; |
||
83 | |||
84 | diag { |
||
85 | label = "wli-tx4-ag300n:red:diag"; |
||
86 | gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
||
87 | }; |
||
88 | |||
89 | led_power: power { |
||
90 | label = "wli-tx4-ag300n:blue:power"; |
||
91 | gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
||
92 | }; |
||
93 | |||
94 | security { |
||
95 | label = "wli-tx4-ag300n:blue:security"; |
||
96 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
||
97 | }; |
||
98 | }; |
||
99 | }; |
||
100 | |||
101 | &gpio0 { |
||
102 | status = "okay"; |
||
103 | }; |
||
104 | |||
105 | ðernet { |
||
106 | status = "okay"; |
||
107 | mtd-mac-address = <&factory 0x4>; |
||
108 | |||
109 | port@0 { |
||
110 | mediatek,fixed-link = <100 1 1 1>; |
||
111 | }; |
||
112 | |||
113 | mdio-bus { |
||
114 | status = "okay"; |
||
115 | |||
116 | phy0: ethernet-phy@0 { |
||
117 | phy-mode = "mii"; |
||
118 | reg = <0>; |
||
119 | }; |
||
120 | }; |
||
121 | }; |
||
122 | |||
123 | &wmac { |
||
124 | ralink,mtd-eeprom = <&factory 0>; |
||
125 | }; |