OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | // SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
2 | /dts-v1/; |
||
3 | |||
4 | #include "mt7620n.dtsi" |
||
5 | |||
6 | #include <dt-bindings/gpio/gpio.h> |
||
7 | #include <dt-bindings/input/input.h> |
||
8 | |||
9 | / { |
||
10 | compatible = "dlink,dwr-922-e2", "ralink,mt7620n-soc"; |
||
11 | model = "D-Link DWR-922 E2"; |
||
12 | |||
13 | aliases { |
||
14 | led-boot = &sstrengthg; |
||
15 | led-failsafe = &sstrengthg; |
||
16 | }; |
||
17 | |||
18 | keys { |
||
19 | compatible = "gpio-keys-polled"; |
||
20 | poll-interval = <20>; |
||
21 | |||
22 | wps { |
||
23 | label = "wps"; |
||
24 | gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
||
25 | linux,code = <KEY_WPS_BUTTON>; |
||
26 | }; |
||
27 | |||
28 | reset { |
||
29 | label = "reset"; |
||
30 | gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
||
31 | linux,code = <KEY_RESTART>; |
||
32 | }; |
||
33 | }; |
||
34 | |||
35 | leds { |
||
36 | compatible = "gpio-leds"; |
||
37 | led-boot = &sstrengthg; |
||
38 | |||
39 | sms { |
||
40 | label = "dwr-922-e2:green:sms"; |
||
41 | gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; |
||
42 | }; |
||
43 | |||
44 | lan { |
||
45 | label = "dwr-922-e2:green:lan"; |
||
46 | gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; |
||
47 | }; |
||
48 | |||
49 | sstrengthg: sstrengthg { |
||
50 | label = "dwr-922-e2:green:sigstrength"; |
||
51 | gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; |
||
52 | }; |
||
53 | |||
54 | sstrengthr { |
||
55 | label = "dwr-922-e2:red:sigstrength"; |
||
56 | gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; |
||
57 | }; |
||
58 | |||
59 | 4g { |
||
60 | label = "dwr-922-e2:green:4g"; |
||
61 | gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; |
||
62 | }; |
||
63 | |||
64 | 3g { |
||
65 | label = "dwr-922-e2:green:3g"; |
||
66 | gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; |
||
67 | }; |
||
68 | |||
69 | wifi { |
||
70 | label = "dwr-922-e2:green:wifi"; |
||
71 | gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; |
||
72 | }; |
||
73 | }; |
||
74 | |||
75 | gpio_export { |
||
76 | compatible = "gpio-export"; |
||
77 | #size-cells = <0>; |
||
78 | |||
79 | lte_modem_enable { |
||
80 | gpio-export,name = "lte_modem_enable"; |
||
81 | gpio-export,output = <1>; |
||
82 | gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; |
||
83 | }; |
||
84 | }; |
||
85 | }; |
||
86 | |||
87 | &gpio1 { |
||
88 | status = "okay"; |
||
89 | }; |
||
90 | |||
91 | &gpio2 { |
||
92 | status = "okay"; |
||
93 | }; |
||
94 | |||
95 | &gpio3 { |
||
96 | status = "okay"; |
||
97 | }; |
||
98 | |||
99 | &spi0 { |
||
100 | status = "okay"; |
||
101 | |||
102 | flash@0 { |
||
103 | compatible = "jedec,spi-nor"; |
||
104 | reg = <0>; |
||
105 | spi-max-frequency = <10000000>; |
||
106 | |||
107 | partitions { |
||
108 | compatible = "fixed-partitions"; |
||
109 | #address-cells = <1>; |
||
110 | #size-cells = <1>; |
||
111 | |||
112 | partition@0 { |
||
113 | label = "jboot"; |
||
114 | reg = <0x0 0x10000>; |
||
115 | read-only; |
||
116 | }; |
||
117 | |||
118 | partition@10000 { |
||
119 | compatible = "amit,jimage"; |
||
120 | label = "firmware"; |
||
121 | reg = <0x10000 0xfe0000>; |
||
122 | }; |
||
123 | |||
124 | config: partition@ff0000 { |
||
125 | label = "config"; |
||
126 | reg = <0xff0000 0x10000>; |
||
127 | read-only; |
||
128 | }; |
||
129 | }; |
||
130 | }; |
||
131 | }; |
||
132 | |||
133 | &ehci { |
||
134 | status = "okay"; |
||
135 | }; |
||
136 | |||
137 | &ohci { |
||
138 | status = "okay"; |
||
139 | }; |
||
140 | |||
141 | ðernet { |
||
142 | port@4 { |
||
143 | status = "okay"; |
||
144 | }; |
||
145 | }; |
||
146 | |||
147 | &pinctrl { |
||
148 | state_default: pinctrl0 { |
||
149 | default { |
||
150 | ralink,group = "spi refclk", "i2c", "ephy", "wled"; |
||
151 | ralink,function = "gpio"; |
||
152 | }; |
||
153 | }; |
||
154 | }; |