OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "mt7620n.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "dlink,dwr-921-c1", "ralink,mt7620n-soc"; |
||
10 | model = "D-Link DWR-921 C1"; |
||
11 | |||
12 | aliases { |
||
13 | led-boot = &led_sstrenghg; |
||
14 | led-failsafe = &led_sstrenghg; |
||
15 | }; |
||
16 | |||
17 | keys { |
||
18 | compatible = "gpio-keys-polled"; |
||
19 | poll-interval = <20>; |
||
20 | |||
21 | wps { |
||
22 | label = "wps"; |
||
23 | gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
||
24 | linux,code = <KEY_WPS_BUTTON>; |
||
25 | }; |
||
26 | |||
27 | reset { |
||
28 | label = "reset"; |
||
29 | gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
||
30 | linux,code = <KEY_RESTART>; |
||
31 | }; |
||
32 | }; |
||
33 | |||
34 | leds { |
||
35 | compatible = "gpio-leds"; |
||
36 | |||
37 | sms { |
||
38 | label = "dwr-921-c1:green:sms"; |
||
39 | gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; |
||
40 | }; |
||
41 | |||
42 | lan { |
||
43 | label = "dwr-921-c1:green:lan"; |
||
44 | gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; |
||
45 | }; |
||
46 | |||
47 | led_sstrenghg: sstrengthg { |
||
48 | label = "dwr-921-c1:green:sigstrength"; |
||
49 | gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; |
||
50 | }; |
||
51 | |||
52 | sstrengthr { |
||
53 | label = "dwr-921-c1:red:sigstrength"; |
||
54 | gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; |
||
55 | }; |
||
56 | |||
57 | 4g { |
||
58 | label = "dwr-921-c1:green:4g"; |
||
59 | gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; |
||
60 | }; |
||
61 | |||
62 | 3g { |
||
63 | label = "dwr-921-c1:green:3g"; |
||
64 | gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; |
||
65 | }; |
||
66 | |||
67 | wifi { |
||
68 | label = "dwr-921-c1:green:wifi"; |
||
69 | gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; |
||
70 | }; |
||
71 | }; |
||
72 | |||
73 | gpio_export { |
||
74 | compatible = "gpio-export"; |
||
75 | #size-cells = <0>; |
||
76 | |||
77 | lte_modem_enable { |
||
78 | gpio-export,name = "lte_modem_enable"; |
||
79 | gpio-export,output = <1>; |
||
80 | gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; |
||
81 | }; |
||
82 | }; |
||
83 | }; |
||
84 | |||
85 | &gpio1 { |
||
86 | status = "okay"; |
||
87 | }; |
||
88 | |||
89 | &gpio2 { |
||
90 | status = "okay"; |
||
91 | }; |
||
92 | |||
93 | &gpio3 { |
||
94 | status = "okay"; |
||
95 | }; |
||
96 | |||
97 | &spi0 { |
||
98 | status = "okay"; |
||
99 | |||
100 | flash@0 { |
||
101 | compatible = "jedec,spi-nor"; |
||
102 | reg = <0>; |
||
103 | spi-max-frequency = <10000000>; |
||
104 | |||
105 | partitions { |
||
106 | compatible = "fixed-partitions"; |
||
107 | #address-cells = <1>; |
||
108 | #size-cells = <1>; |
||
109 | |||
110 | partition@0 { |
||
111 | label = "jboot"; |
||
112 | reg = <0x0 0x10000>; |
||
113 | read-only; |
||
114 | }; |
||
115 | |||
116 | partition@10000 { |
||
117 | compatible = "amit,jimage"; |
||
118 | label = "firmware"; |
||
119 | reg = <0x10000 0xfe0000>; |
||
120 | }; |
||
121 | |||
122 | config: partition@ff0000 { |
||
123 | label = "config"; |
||
124 | reg = <0xff0000 0x10000>; |
||
125 | read-only; |
||
126 | }; |
||
127 | }; |
||
128 | }; |
||
129 | }; |
||
130 | |||
131 | &ehci { |
||
132 | status = "okay"; |
||
133 | }; |
||
134 | |||
135 | &ohci { |
||
136 | status = "okay"; |
||
137 | }; |
||
138 | |||
139 | ðernet { |
||
140 | port@4 { |
||
141 | status = "okay"; |
||
142 | }; |
||
143 | }; |
||
144 | |||
145 | &pinctrl { |
||
146 | state_default: pinctrl0 { |
||
147 | default { |
||
148 | ralink,group = "spi refclk", "i2c", "ephy", "wled"; |
||
149 | ralink,function = "gpio"; |
||
150 | }; |
||
151 | }; |
||
152 | }; |