OpenWrt – Blame information for rev 4
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /* Copyright (c) 2015, The Linux Foundation. All rights reserved. |
2 | * Copyright (c) 2017, Sven Eckelmann <sven.eckelmann@openmesh.com> |
||
3 | * |
||
4 | * Permission to use, copy, modify, and/or distribute this software for any |
||
5 | * purpose with or without fee is hereby granted, provided that the above |
||
6 | * copyright notice and this permission notice appear in all copies. |
||
7 | * |
||
8 | * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
||
9 | * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
||
10 | * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
||
11 | * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
||
12 | * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
||
13 | * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
||
14 | * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
||
15 | * |
||
16 | */ |
||
17 | |||
18 | #include "qcom-ipq4019.dtsi" |
||
19 | #include <dt-bindings/gpio/gpio.h> |
||
20 | #include <dt-bindings/input/input.h> |
||
21 | #include <dt-bindings/soc/qcom,tcsr.h> |
||
22 | |||
23 | / { |
||
24 | model = "OpenMesh A42"; |
||
25 | compatible = "openmesh,a42", "qcom,ipq4019"; |
||
26 | |||
27 | soc { |
||
28 | mdio@90000 { |
||
29 | status = "okay"; |
||
30 | }; |
||
31 | |||
32 | ess-psgmii@98000 { |
||
33 | status = "okay"; |
||
34 | }; |
||
35 | |||
36 | tcsr@194b000 { |
||
37 | /* select hostmode */ |
||
38 | compatible = "qcom,tcsr"; |
||
39 | reg = <0x194b000 0x100>; |
||
40 | qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; |
||
41 | status = "okay"; |
||
42 | }; |
||
43 | |||
44 | tcsr@1949000 { |
||
45 | compatible = "qcom,tcsr"; |
||
46 | reg = <0x1949000 0x100>; |
||
47 | qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; |
||
48 | }; |
||
49 | |||
50 | ess_tcsr@1953000 { |
||
51 | compatible = "qcom,tcsr"; |
||
52 | reg = <0x1953000 0x1000>; |
||
53 | qcom,ess-interface-select = <TCSR_ESS_PSGMII>; |
||
54 | }; |
||
55 | |||
56 | tcsr@1957000 { |
||
57 | compatible = "qcom,tcsr"; |
||
58 | reg = <0x1957000 0x100>; |
||
59 | qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; |
||
60 | }; |
||
61 | |||
62 | usb2: usb2@60f8800 { |
||
63 | status = "okay"; |
||
64 | }; |
||
65 | |||
66 | crypto@8e3a000 { |
||
67 | status = "okay"; |
||
68 | }; |
||
69 | |||
70 | watchdog@b017000 { |
||
71 | status = "okay"; |
||
72 | }; |
||
73 | |||
74 | ess-switch@c000000 { |
||
75 | status = "okay"; |
||
76 | }; |
||
77 | |||
78 | edma@c080000 { |
||
79 | status = "okay"; |
||
80 | }; |
||
81 | }; |
||
82 | |||
83 | keys { |
||
84 | compatible = "gpio-keys"; |
||
85 | |||
86 | reset { |
||
87 | label = "reset"; |
||
88 | gpios = <&tlmm 59 GPIO_ACTIVE_LOW>; |
||
89 | linux,code = <KEY_RESTART>; |
||
90 | }; |
||
91 | }; |
||
92 | |||
93 | aliases { |
||
94 | led-boot = &power; |
||
95 | led-failsafe = &power; |
||
96 | led-running = &power; |
||
97 | led-upgrade = &power; |
||
98 | }; |
||
99 | |||
100 | leds { |
||
101 | compatible = "gpio-leds"; |
||
102 | |||
103 | red { |
||
104 | label = "a42:red:status"; |
||
105 | gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; |
||
106 | linux,default-trigger = "default-off"; |
||
107 | }; |
||
108 | |||
109 | power: green { |
||
110 | label = "a42:green:status"; |
||
111 | gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>; |
||
112 | }; |
||
113 | |||
114 | blue { |
||
115 | label = "a42:blue:status"; |
||
116 | gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; |
||
117 | linux,default-trigger = "default-off"; |
||
118 | }; |
||
119 | }; |
||
120 | |||
121 | watchdog { |
||
122 | compatible = "linux,wdt-gpio"; |
||
123 | gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; |
||
124 | hw_algo = "toggle"; |
||
125 | /* hw_margin_ms is actually 300s but driver limits it to 60s */ |
||
126 | hw_margin_ms = <60000>; |
||
127 | always-running; |
||
128 | }; |
||
129 | }; |
||
130 | |||
131 | &tlmm { |
||
132 | serial_pins: serial_pinmux { |
||
133 | mux { |
||
134 | pins = "gpio60", "gpio61"; |
||
135 | function = "blsp_uart0"; |
||
136 | bias-disable; |
||
137 | }; |
||
138 | }; |
||
139 | |||
140 | spi_0_pins: spi_0_pinmux { |
||
141 | pin { |
||
142 | function = "blsp_spi0"; |
||
143 | pins = "gpio55", "gpio56", "gpio57"; |
||
144 | drive-strength = <12>; |
||
145 | bias-disable; |
||
146 | }; |
||
147 | pin_cs { |
||
148 | function = "gpio"; |
||
149 | pins = "gpio54"; |
||
150 | drive-strength = <2>; |
||
151 | bias-disable; |
||
152 | output-high; |
||
153 | }; |
||
154 | }; |
||
155 | }; |
||
156 | |||
157 | &blsp_dma { |
||
158 | status = "okay"; |
||
159 | }; |
||
160 | |||
161 | &blsp1_spi1 { |
||
162 | pinctrl-0 = <&spi_0_pins>; |
||
163 | pinctrl-names = "default"; |
||
164 | status = "okay"; |
||
165 | cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; |
||
166 | |||
167 | m25p80@0 { |
||
168 | #address-cells = <1>; |
||
169 | #size-cells = <1>; |
||
170 | compatible = "jedec,spi-nor"; |
||
171 | reg = <0>; |
||
172 | spi-max-frequency = <24000000>; |
||
173 | /* partitions are passed via bootloader */ |
||
174 | }; |
||
175 | }; |
||
176 | |||
177 | &blsp1_uart1 { |
||
178 | pinctrl-0 = <&serial_pins>; |
||
179 | pinctrl-names = "default"; |
||
180 | status = "okay"; |
||
181 | }; |
||
182 | |||
183 | &cryptobam { |
||
184 | status = "okay"; |
||
185 | }; |
||
186 | |||
187 | &gmac0 { |
||
188 | qcom,phy_mdio_addr = <4>; |
||
189 | qcom,poll_required = <1>; |
||
190 | qcom,forced_speed = <1000>; |
||
191 | qcom,forced_duplex = <1>; |
||
192 | vlan_tag = <2 0x20>; |
||
193 | }; |
||
194 | |||
195 | &gmac1 { |
||
196 | qcom,phy_mdio_addr = <3>; |
||
197 | qcom,poll_required = <1>; |
||
198 | qcom,forced_speed = <1000>; |
||
199 | qcom,forced_duplex = <1>; |
||
200 | vlan_tag = <1 0x10>; |
||
201 | }; |
||
202 | |||
203 | &usb2_hs_phy { |
||
204 | status = "okay"; |
||
205 | }; |
||
206 | |||
207 | &wifi0 { |
||
208 | status = "okay"; |
||
209 | qcom,ath10k-calibration-variant = "OM-A42"; |
||
210 | }; |
||
211 | |||
212 | &wifi1 { |
||
213 | status = "okay"; |
||
214 | qcom,ath10k-calibration-variant = "OM-A42"; |
||
215 | }; |