OpenWrt – Blame information for rev 1

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "qca956x.dtsi"
8  
9 / {
10 model = "ROSINSON WR818";
11 compatible = "rosinson,wr818", "qca,qca9560";
12  
13 chosen {
14 bootargs = "console=ttyS0,115200n8";
15 };
16  
17 aliases {
18 led-boot = &system;
19 led-failsafe = &system;
20 led-running = &system;
21 led-upgrade = &system;
22 };
23  
24 gpio_leds: leds {
25 compatible = "gpio-leds";
26  
27 system: system {
28 label = "wr818:red:system";
29 gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
30 };
31  
32 wifi_2g {
33 label = "wr818:red:wifi2g";
34 gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
35 linux,default-trigger = "phy0tpt";
36 };
37 };
38  
39 keys {
40 compatible = "gpio-keys";
41  
42 reset {
43 label = "reset";
44 linux,code = <KEY_RESTART>;
45 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
46 debounce-interval = <60>;
47 };
48 };
49 };
50  
51 &uart {
52 status = "okay";
53 };
54  
55 &gpio {
56 status = "okay";
57 };
58  
59 &spi {
60 num-cs = <1>;
61  
62 status = "okay";
63  
64 flash@0 {
65 compatible = "jedec,spi-nor";
66 reg = <0>;
67 spi-max-frequency = <25000000>;
68  
69 partitions {
70 compatible = "fixed-partitions";
71 #address-cells = <1>;
72 #size-cells = <1>;
73  
74 partition@0 {
75 label = "u-boot";
76 reg = <0x000000 0x040000>;
77 read-only;
78 };
79  
80 partition@40000 {
81 label = "u-boot-env";
82 reg = <0x040000 0x010000>;
83 read-only;
84 };
85  
86 info: partition@50000 {
87 label = "factory";
88 reg = <0x050000 0x010000>;
89 read-only;
90 };
91  
92 partition@60000 {
93 compatible = "denx,uimage";
94 label = "firmware";
95 reg = <0x060000 0xf80000>;
96 };
97  
98 art: partition@ff0000 {
99 label = "art";
100 reg = <0xff0000 0x010000>;
101 read-only;
102 };
103 };
104 };
105 };
106  
107 &mdio0 {
108 status = "okay";
109  
110 phy-mask = <0>;
111 phy0: ethernet-phy@0 {
112 reg = <0>;
113 phy-mode = "sgmii";
114  
115 qca,ar8327-initvals = <
116 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
117 0x7c 0x0000007e /* PORT0_STATUS */
118 >;
119 };
120 };
121  
122 &eth0 {
123 status = "okay";
124  
125 mtd-mac-address = <&info 0x0>;
126 phy-mode = "sgmii";
127 phy-handle = <&phy0>;
128 };
129  
130 &wmac {
131 status = "okay";
132 mtd-cal-data = <&art 0x1000>;
133 };
134  
135 &usb_phy0 {
136 status = "okay";
137 };
138  
139 &usb0 {
140 #address-cells = <1>;
141 #size-cells = <0>;
142 status = "okay";
143  
144 port@1 {
145 reg = <1>;
146 #trigger-source-cells = <0>;
147 };
148 };
149  
150 &usb_phy1 {
151 status = "okay";
152 };
153  
154 &usb1 {
155 #address-cells = <1>;
156 #size-cells = <0>;
157 status = "okay";
158  
159 port@2 {
160 reg = <2>;
161 #trigger-source-cells = <0>;
162 };
163 };