OpenWrt – Blame information for rev 1

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "qca956x.dtsi"
8  
9 / {
10 model = "NEC Aterm WG800HP";
11 compatible = "nec,wg800hp", "qca,qca9563";
12  
13 chosen {
14 bootargs = "console=ttyS0,115200n8";
15 };
16  
17 aliases {
18 led-boot = &power_green;
19 led-failsafe = &power_red;
20 led-running = &power_green;
21 led-upgrade = &power_green;
22 };
23  
24 leds {
25 compatible = "gpio-leds";
26 pinctrl-names = "default";
27 pinctrl-0 = <&jtag_disable_pins>;
28  
29 wlan2g_red {
30 label = "wg800hp:red:wlan2g";
31 gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
32 };
33  
34 active_red {
35 label = "wg800hp:red:active";
36 gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
37 };
38  
39 active_green {
40 label = "wg800hp:green:active";
41 gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
42 };
43  
44 power_red: power_red {
45 label = "wg800hp:red:power";
46 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
47 };
48  
49 power_green: power_green {
50 label = "wg800hp:green:power";
51 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
52 default-state = "on";
53 };
54  
55 wlan5g_red {
56 label = "wg800hp:red:wlan5g";
57 gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
58 };
59  
60 wlan5g_green {
61 label = "wg800hp:green:wlan5g";
62 gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
63 linux,default-trigger = "phy0tpt";
64 };
65  
66 wlan2g_green {
67 label = "wg800hp:green:wlan2g";
68 gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
69 linux,default-trigger = "phy1tpt";
70 };
71 };
72  
73 keys {
74 compatible = "gpio-keys";
75  
76 br {
77 label = "br";
78 gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
79 linux,code = <BTN_0>;
80 linux,input-type = <EV_SW>;
81 debounce-interval = <60>;
82 };
83  
84 reset {
85 label = "reset";
86 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
87 linux,code = <KEY_RESTART>;
88 debounce-interval = <60>;
89 };
90  
91 wps {
92 label = "wps";
93 gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
94 linux,code = <KEY_WPS_BUTTON>;
95 debounce-interval = <60>;
96 };
97 };
98 };
99  
100 &spi {
101 status = "okay";
102 num-cs = <1>;
103  
104 flash@0 {
105 compatible = "jedec,spi-nor";
106 reg = <0>;
107 spi-max-frequency = <25000000>;
108  
109 partitions {
110 compatible = "fixed-partitions";
111 #address-cells = <1>;
112 #size-cells = <1>;
113  
114 partition@0 {
115 label = "u-boot";
116 reg = <0x000000 0x040000>;
117 read-only;
118 };
119  
120 partition@40000 {
121 label = "u-boot-env";
122 reg = <0x040000 0x010000>;
123 read-only;
124 };
125  
126 partition@50000 {
127 compatible = "denx,uimage";
128 label = "firmware";
129 reg = <0x050000 0x6f0000>;
130 };
131  
132 partition@740000 {
133 label = "user_data";
134 reg = <0x740000 0x0a0000>;
135 read-only;
136 };
137  
138 partition@7e0000 {
139 label = "board_data";
140 reg = <0x7e0000 0x010000>;
141 read-only;
142 };
143  
144 art: partition@7f0000 {
145 label = "art";
146 reg = <0x7f0000 0x010000>;
147 read-only;
148 };
149 };
150 };
151 };
152  
153 &mdio0 {
154 status = "okay";
155  
156 phy0: ethernet-phy@0 {
157 reg = <0>;
158  
159 qca,ar8327-initvals = <
160 0x04 0x00000080 /* PORT0 PAD MODE CTRL */
161 0x50 0xcc35cc35 /* LED_CTRL0 */
162 0x54 0xca35ca35 /* LED_CTRL1 */
163 0x58 0xc935c935 /* LED_CTRL2 */
164 0x5c 0x03ffff00 /* LED_CTRL3 */
165 0x7c 0x0000007e /* PORT0_STATUS */
166 >;
167 };
168 };
169  
170 &eth0 {
171 status = "okay";
172  
173 phy-mode = "sgmii";
174 phy-handle = <&phy0>;
175 };
176  
177 &pcie {
178 status = "okay";
179 };
180  
181 &uart {
182 status = "okay";
183 };
184  
185 &wmac {
186 status = "okay";
187 qca,no-eeprom;
188 };