OpenWrt – Blame information for rev 1

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3  
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6  
7 #include "qca9557.dtsi"
8  
9 / {
10 chosen {
11 bootargs = "console=ttyS0,115200n8";
12 };
13  
14 aliases {
15 led-boot = &system;
16 led-failsafe = &system;
17 led-running = &system;
18 led-upgrade = &system;
19 };
20  
21 gpio_leds: leds {
22 compatible = "gpio-leds";
23  
24 system: system {
25 label = "tp-link:green:system";
26 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
27 default-state = "on";
28 };
29  
30 usb1 {
31 label = "tp-link:green:usb1";
32 gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
33 trigger-sources = <&hub_port1>;
34 linux,default-trigger = "usbport";
35 };
36  
37 usb2 {
38 label = "tp-link:green:usb2";
39 gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
40 trigger-sources = <&hub_port0>;
41 linux,default-trigger = "usbport";
42 };
43  
44 led_wlan2g: wlan2g {
45 label = "tp-link:green:wlan2g";
46 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
47 linux,default-trigger = "phy1tpt";
48 };
49  
50 qss {
51 label = "tp-link:green:qss";
52 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
53 };
54 };
55  
56 gpio_keys: keys {
57 compatible = "gpio-keys";
58  
59 reset {
60 label = "Reset button";
61 linux,code = <KEY_RESTART>;
62 gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
63 debounce-interval = <60>;
64 };
65 };
66  
67 gpio-export {
68 compatible = "gpio-export";
69  
70 gpio_usb1_power {
71 gpio-export,name = "tp-link:power:usb1";
72 gpio-export,output = <1>;
73 gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
74 };
75  
76 gpio_usb2_power {
77 gpio-export,name = "tp-link:power:usb2";
78 gpio-export,output = <1>;
79 gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
80 };
81  
82 };
83 };
84  
85 &pcie1 {
86 status = "okay";
87 };
88  
89 &uart {
90 status = "okay";
91 };
92  
93 &gpio {
94 status = "okay";
95 };
96  
97 &usb_phy0 {
98 status = "okay";
99 };
100  
101 &usb0 {
102 #address-cells = <1>;
103 #size-cells = <0>;
104 status = "okay";
105  
106 hub_port0: port@1 {
107 reg = <1>;
108 #trigger-source-cells = <0>;
109 };
110 };
111  
112 &usb_phy1 {
113 status = "okay";
114 };
115  
116 &usb1 {
117 #address-cells = <1>;
118 #size-cells = <0>;
119 status = "okay";
120  
121 hub_port1: port@1 {
122 reg = <1>;
123 #trigger-source-cells = <0>;
124 };
125 };
126  
127 &spi {
128 status = "okay";
129 num-cs = <1>;
130  
131 flash@0 {
132 compatible = "jedec,spi-nor";
133 reg = <0>;
134 spi-max-frequency = <25000000>;
135  
136 mtdparts: partitions {
137 compatible = "fixed-partitions";
138 #address-cells = <1>;
139 #size-cells = <1>;
140 };
141 };
142 };
143  
144 &mdio0 {
145 status = "okay";
146  
147 phy0: ethernet-phy@0 {
148 reg = <0>;
149  
150 qca,ar8327-initvals = <
151 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
152 0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
153 0x50 0xc737c737 /* LED_CTRL0 */
154 0x54 0x00000000 /* LED_CTRL1 */
155 0x58 0x00000000 /* LED_CTRL2 */
156 0x5c 0x0030c300 /* LED_CTRL3 */
157 0x7c 0x0000007e /* PORT0_STATUS */
158 0x94 0x0000007e /* PORT6 STATUS */
159 >;
160 };
161 };
162  
163 &eth0 {
164 status = "okay";
165  
166 mtd-mac-address = <&uboot 0x1fc00>;
167 mtd-mac-address-increment = <1>;
168 phy-handle = <&phy0>;
169 pll-data = <0x56000000 0x00000101 0x00001616>;
170  
171 gmac-config {
172 device = <&gmac>;
173 rgmii-enabled = <1>;
174 };
175 };
176  
177 &eth1 {
178 status = "okay";
179  
180 mtd-mac-address = <&uboot 0x1fc00>;
181 pll-data = <0x03000101 0x00000101 0x00001616>;
182  
183 fixed-link {
184 speed = <1000>;
185 full-duplex;
186 };
187 };
188  
189 &wmac {
190 status = "okay";
191 mtd-cal-data = <&art 0x1000>;
192 mtd-mac-address = <&uboot 0x1fc00>;
193 };