OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | // SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
2 | /dts-v1/; |
||
3 | |||
4 | #include <dt-bindings/gpio/gpio.h> |
||
5 | #include <dt-bindings/input/input.h> |
||
6 | |||
7 | #include "ar9344.dtsi" |
||
8 | |||
9 | / { |
||
10 | model = "OCEDO Raccoon"; |
||
11 | compatible = "ocedo,raccoon", "qca,ar9344"; |
||
12 | |||
13 | chosen { |
||
14 | bootargs = "console=ttyS0,115200n8"; |
||
15 | }; |
||
16 | |||
17 | aliases { |
||
18 | led-boot = &system; |
||
19 | led-failsafe = &system; |
||
20 | led-running = &system; |
||
21 | led-upgrade = &system; |
||
22 | }; |
||
23 | |||
24 | leds { |
||
25 | compatible = "gpio-leds"; |
||
26 | |||
27 | power { |
||
28 | label = "raccoon:green:power"; |
||
29 | gpios = <&gpio 14 GPIO_ACTIVE_LOW>; |
||
30 | default-state = "on"; |
||
31 | }; |
||
32 | |||
33 | wlan2g { |
||
34 | label = "raccoon:yellow:wlan24"; |
||
35 | gpios = <&gpio 12 GPIO_ACTIVE_LOW>; |
||
36 | linux,default-trigger = "phy0tpt"; |
||
37 | }; |
||
38 | |||
39 | system: system { |
||
40 | label = "raccoon:blue:sys"; |
||
41 | gpios = <&gpio 13 GPIO_ACTIVE_LOW>; |
||
42 | }; |
||
43 | }; |
||
44 | |||
45 | ath9k-leds { |
||
46 | compatible = "gpio-leds"; |
||
47 | |||
48 | wlan5g { |
||
49 | label = "raccoon:red:wlan5"; |
||
50 | gpios = <&ath9k 0 GPIO_ACTIVE_LOW>; |
||
51 | linux,default-trigger = "phy1tpt"; |
||
52 | }; |
||
53 | }; |
||
54 | |||
55 | keys { |
||
56 | compatible = "gpio-keys-polled"; |
||
57 | poll-interval = <20>; |
||
58 | |||
59 | reset { |
||
60 | linux,code = <KEY_RESTART>; |
||
61 | gpios = <&gpio 17 GPIO_ACTIVE_LOW>; |
||
62 | debounce-interval = <60>; |
||
63 | }; |
||
64 | }; |
||
65 | }; |
||
66 | |||
67 | &ref { |
||
68 | clock-frequency = <40000000>; |
||
69 | }; |
||
70 | |||
71 | &uart { |
||
72 | status = "okay"; |
||
73 | }; |
||
74 | |||
75 | &gpio { |
||
76 | status = "okay"; |
||
77 | }; |
||
78 | |||
79 | &spi { |
||
80 | num-cs = <1>; |
||
81 | |||
82 | status = "okay"; |
||
83 | |||
84 | flash@0 { |
||
85 | compatible = "jedec,spi-nor"; |
||
86 | reg = <0>; |
||
87 | spi-max-frequency = <25000000>; |
||
88 | |||
89 | partitions { |
||
90 | compatible = "fixed-partitions"; |
||
91 | #address-cells = <1>; |
||
92 | #size-cells = <1>; |
||
93 | |||
94 | uboot: partition@0 { |
||
95 | label = "u-boot"; |
||
96 | reg = <0x000000 0x040000>; |
||
97 | read-only; |
||
98 | }; |
||
99 | |||
100 | partition@40000 { |
||
101 | label = "u-boot-env"; |
||
102 | reg = <0x040000 0x010000>; |
||
103 | }; |
||
104 | |||
105 | partition@50000 { |
||
106 | compatible = "denx,uimage"; |
||
107 | label = "firmware"; |
||
108 | reg = <0x050000 0x740000>; |
||
109 | }; |
||
110 | |||
111 | partition@790000 { |
||
112 | label = "vendor"; |
||
113 | reg = <0x790000 0x740000>; |
||
114 | read-only; |
||
115 | }; |
||
116 | |||
117 | partition@ed0000 { |
||
118 | label = "data"; |
||
119 | reg = <0xed0000 0x110000>; |
||
120 | read-only; |
||
121 | }; |
||
122 | |||
123 | partition@fe0000 { |
||
124 | label = "id"; |
||
125 | reg = <0xfe0000 0x010000>; |
||
126 | read-only; |
||
127 | }; |
||
128 | |||
129 | art: partition@ff0000 { |
||
130 | label = "art"; |
||
131 | reg = <0xff0000 0x010000>; |
||
132 | read-only; |
||
133 | }; |
||
134 | }; |
||
135 | }; |
||
136 | }; |
||
137 | |||
138 | &pcie { |
||
139 | status = "okay"; |
||
140 | |||
141 | ath9k: wifi@0,0 { |
||
142 | compatible = "pci168c,0030"; |
||
143 | reg = <0x0000 0 0 0 0>; |
||
144 | mtd-mac-address = <&art 0xc>; |
||
145 | qca,no-eeprom; |
||
146 | #gpio-cells = <2>; |
||
147 | gpio-controller; |
||
148 | }; |
||
149 | }; |
||
150 | |||
151 | &wmac { |
||
152 | status = "okay"; |
||
153 | |||
154 | mtd-cal-data = <&art 0x1000>; |
||
155 | mtd-mac-address = <&art 0x6>; |
||
156 | }; |
||
157 | |||
158 | &mdio0 { |
||
159 | status = "okay"; |
||
160 | |||
161 | phy-mask = <0>; |
||
162 | |||
163 | phy0: ethernet-phy@0 { |
||
164 | reg = <0>; |
||
165 | phy-mode = "rgmii"; |
||
166 | }; |
||
167 | }; |
||
168 | |||
169 | ð0 { |
||
170 | status = "okay"; |
||
171 | |||
172 | /* default for ar934x, except for 1000M */ |
||
173 | pll-data = <0x06000000 0x00000101 0x00001616>; |
||
174 | |||
175 | mtd-mac-address = <&art 0x0>; |
||
176 | |||
177 | phy-mode = "rgmii"; |
||
178 | phy-handle = <&phy0>; |
||
179 | }; |