OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | // SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
2 | /dts-v1/; |
||
3 | |||
4 | #include <dt-bindings/gpio/gpio.h> |
||
5 | #include <dt-bindings/input/input.h> |
||
6 | |||
7 | #include "ar9331.dtsi" |
||
8 | |||
9 | / { |
||
10 | model = "Pisen WMM003N"; |
||
11 | compatible = "pisen,wmm003n", "qca,ar9331"; |
||
12 | |||
13 | aliases { |
||
14 | serial0 = &uart; |
||
15 | led-boot = &led_system; |
||
16 | led-failsafe = &led_system; |
||
17 | led-running = &led_system; |
||
18 | led-upgrade = &led_system; |
||
19 | }; |
||
20 | |||
21 | keys { |
||
22 | compatible = "gpio-keys-polled"; |
||
23 | poll-interval = <20>; |
||
24 | |||
25 | reset { |
||
26 | label = "reset"; |
||
27 | linux,code = <KEY_RESTART>; |
||
28 | gpios = <&gpio 12 GPIO_ACTIVE_LOW>; |
||
29 | debounce-interval = <60>; |
||
30 | }; |
||
31 | }; |
||
32 | |||
33 | leds { |
||
34 | compatible = "gpio-leds"; |
||
35 | |||
36 | led_system: system { |
||
37 | label = "pisen:blue:system"; |
||
38 | gpios = <&gpio 0 GPIO_ACTIVE_LOW>; |
||
39 | }; |
||
40 | }; |
||
41 | |||
42 | reg_usb_vbus: reg_usb_vbus { |
||
43 | compatible = "regulator-fixed"; |
||
44 | regulator-name = "usb_vbus"; |
||
45 | regulator-min-microvolt = <5000000>; |
||
46 | regulator-max-microvolt = <5000000>; |
||
47 | gpio = <&gpio 8 GPIO_ACTIVE_HIGH>; |
||
48 | enable-active-high; |
||
49 | }; |
||
50 | }; |
||
51 | |||
52 | &spi { |
||
53 | status = "okay"; |
||
54 | num-cs = <1>; |
||
55 | |||
56 | flash@0 { |
||
57 | compatible = "jedec,spi-nor"; |
||
58 | reg = <0>; |
||
59 | spi-max-frequency = <25000000>; |
||
60 | |||
61 | partitions { |
||
62 | compatible = "fixed-partitions"; |
||
63 | #address-cells = <1>; |
||
64 | #size-cells = <1>; |
||
65 | |||
66 | uboot: partition@0 { |
||
67 | reg = <0x0 0x20000>; |
||
68 | label = "u-boot"; |
||
69 | read-only; |
||
70 | }; |
||
71 | |||
72 | firmware: partition@20000 { |
||
73 | compatible = "tplink,firmware"; |
||
74 | reg = <0x20000 0x7d0000>; |
||
75 | label = "firmware"; |
||
76 | }; |
||
77 | |||
78 | art: partition@7f0000 { |
||
79 | reg = <0x7f0000 0x10000>; |
||
80 | label = "art"; |
||
81 | read-only; |
||
82 | }; |
||
83 | }; |
||
84 | }; |
||
85 | }; |
||
86 | |||
87 | ð0 { |
||
88 | status = "okay"; |
||
89 | |||
90 | mtd-mac-address = <&uboot 0x1fc00>; |
||
91 | |||
92 | gmac-config { |
||
93 | device = <&gmac>; |
||
94 | |||
95 | switch-phy-addr-swap = <0>; |
||
96 | switch-phy-swap = <0>; |
||
97 | }; |
||
98 | }; |
||
99 | |||
100 | ð1 { |
||
101 | status = "okay"; |
||
102 | compatible = "syscon", "simple-mfd"; |
||
103 | }; |
||
104 | |||
105 | &gpio { |
||
106 | status = "okay"; |
||
107 | }; |
||
108 | |||
109 | &uart { |
||
110 | status = "okay"; |
||
111 | }; |
||
112 | |||
113 | &usb { |
||
114 | dr_mode = "host"; |
||
115 | vbus-supply = <®_usb_vbus>; |
||
116 | status = "okay"; |
||
117 | }; |
||
118 | |||
119 | &usb_phy { |
||
120 | status = "okay"; |
||
121 | }; |
||
122 | |||
123 | &wmac { |
||
124 | status = "okay"; |
||
125 | mtd-cal-data = <&art 0x1000>; |
||
126 | mtd-mac-address = <&uboot 0x1fc00>; |
||
127 | }; |