OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | // SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
2 | /dts-v1/; |
||
3 | |||
4 | #include <dt-bindings/gpio/gpio.h> |
||
5 | #include <dt-bindings/input/input.h> |
||
6 | |||
7 | #include "ar9331.dtsi" |
||
8 | |||
9 | / { |
||
10 | model = "eTactica EG200"; |
||
11 | compatible = "etactica,eg200", "qca,ar9331"; |
||
12 | |||
13 | aliases { |
||
14 | serial0 = &uart; |
||
15 | }; |
||
16 | |||
17 | keys { |
||
18 | compatible = "gpio-keys-polled"; |
||
19 | poll-interval = <50>; |
||
20 | |||
21 | restore { |
||
22 | linux,code = <KEY_WPS_BUTTON>; |
||
23 | gpios = <&gpio 11 GPIO_ACTIVE_LOW>; |
||
24 | }; |
||
25 | }; |
||
26 | |||
27 | leds { |
||
28 | compatible = "gpio-leds"; |
||
29 | |||
30 | modbus { |
||
31 | label = "eg200:red:modbus"; |
||
32 | gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; |
||
33 | }; |
||
34 | |||
35 | etactica { |
||
36 | label = "eg200:red:etactica"; |
||
37 | gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; |
||
38 | }; |
||
39 | |||
40 | eth0 { |
||
41 | label = "eg200:red:eth0"; |
||
42 | gpios = <&gpio 13 GPIO_ACTIVE_LOW>; |
||
43 | }; |
||
44 | |||
45 | wlan { |
||
46 | label = "eg200:red:wlan"; |
||
47 | gpios = <&gpio 0 GPIO_ACTIVE_LOW>; |
||
48 | linux,default-trigger = "phy0tpt"; |
||
49 | }; |
||
50 | }; |
||
51 | }; |
||
52 | |||
53 | &uart { |
||
54 | status = "okay"; |
||
55 | }; |
||
56 | |||
57 | &gpio { |
||
58 | status = "okay"; |
||
59 | }; |
||
60 | |||
61 | &usb { |
||
62 | dr_mode = "host"; |
||
63 | status = "okay"; |
||
64 | }; |
||
65 | |||
66 | &usb_phy { |
||
67 | status = "okay"; |
||
68 | }; |
||
69 | |||
70 | ð0 { |
||
71 | status = "okay"; |
||
72 | mtd-mac-address = <&art 0x0>; |
||
73 | |||
74 | gmac-config { |
||
75 | device = <&gmac>; |
||
76 | switch-phy-addr-swap = <1>; |
||
77 | switch-phy-swap = <1>; |
||
78 | }; |
||
79 | }; |
||
80 | |||
81 | ð1 { |
||
82 | status = "okay"; |
||
83 | compatible = "syscon", "simple-mfd"; |
||
84 | }; |
||
85 | |||
86 | &spi { |
||
87 | num-chipselects = <1>; |
||
88 | status = "okay"; |
||
89 | |||
90 | flash@0 { |
||
91 | compatible = "jedec,spi-nor"; |
||
92 | spi-max-frequency = <50000000>; |
||
93 | reg = <0>; |
||
94 | |||
95 | partitions { |
||
96 | compatible = "fixed-partitions"; |
||
97 | #address-cells = <1>; |
||
98 | #size-cells = <1>; |
||
99 | |||
100 | uboot@0 { |
||
101 | reg = <0x0 0x40000>; |
||
102 | read-only; |
||
103 | }; |
||
104 | |||
105 | uboot-env@40000 { |
||
106 | reg = <0x40000 0x10000>; |
||
107 | read-only; |
||
108 | }; |
||
109 | |||
110 | firmware@50000 { |
||
111 | compatible = "denx,uimage"; |
||
112 | reg = <0x50000 0xfa0000>; |
||
113 | }; |
||
114 | |||
115 | art: art@ff0000 { |
||
116 | reg = <0xff0000 0x10000>; |
||
117 | read-only; |
||
118 | }; |
||
119 | }; |
||
120 | }; |
||
121 | }; |
||
122 | |||
123 | &wmac { |
||
124 | status = "okay"; |
||
125 | mtd-cal-data = <&art 0x1000>; |
||
126 | mtd-mac-address = <&art 0x1002>; |
||
127 | }; |