OpenWrt – Blame information for rev 4
?pathlinks?
| Rev | Author | Line No. | Line |
|---|---|---|---|
| 4 | office | 1 | |
| 2 | #include <dt-bindings/interrupt-controller/irq.h> |
||
| 3 | #include <dt-bindings/gpio/gpio.h> |
||
| 4 | |||
| 5 | / { |
||
| 6 | compatible = "lantiq,easy98000", "lantiq,falcon"; |
||
| 7 | |||
| 8 | memory@0 { |
||
| 9 | device_type = "memory"; |
||
| 10 | reg = <0x0 0x4000000>; |
||
| 11 | }; |
||
| 12 | |||
| 13 | easy98000-leds { |
||
| 14 | compatible = "gpio-leds"; |
||
| 15 | pinctrl-names = "default"; |
||
| 16 | pinctrl-0 = <&bootled_pins>; |
||
| 17 | |||
| 18 | LED_0 { |
||
| 19 | label = "easy98000:green:gpon"; |
||
| 20 | gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; |
||
| 21 | default-state = "keep"; |
||
| 22 | }; |
||
| 23 | LED_1 { |
||
| 24 | label = "easy98000:red:gpon"; |
||
| 25 | gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>; |
||
| 26 | default-state = "keep"; |
||
| 27 | }; |
||
| 28 | LED_2 { |
||
| 29 | label = "easy98000:green:gpon_tx"; |
||
| 30 | gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; |
||
| 31 | default-state = "keep"; |
||
| 32 | }; |
||
| 33 | LED_3 { |
||
| 34 | label = "easy98000:green:gpon_rx"; |
||
| 35 | gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; |
||
| 36 | default-state = "keep"; |
||
| 37 | }; |
||
| 38 | LED_4 { |
||
| 39 | label = "easy98000:green:voice"; |
||
| 40 | gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; |
||
| 41 | default-state = "keep"; |
||
| 42 | }; |
||
| 43 | LED_5 { |
||
| 44 | label = "easy98000:green:status"; |
||
| 45 | gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; |
||
| 46 | default-state = "keep"; |
||
| 47 | }; |
||
| 48 | }; |
||
| 49 | }; |
||
| 50 | |||
| 51 | &ebu_cs1 { |
||
| 52 | eth0: ethernet@0000000 { |
||
| 53 | compatible = "davicom,dm9000"; |
||
| 54 | device_type = "network"; |
||
| 55 | reg = <0x0000003 0x1>, <0x0000001 0x1>; |
||
| 56 | reg-names = "addr", "data"; |
||
| 57 | interrupt-parent = <&gpio1>; |
||
| 58 | #interrupt-cells = <2>; |
||
| 59 | interrupts = <10 IRQ_TYPE_LEVEL_LOW>; |
||
| 60 | local-mac-address = [ 00 00 00 00 00 00 ]; |
||
| 61 | }; |
||
| 62 | |||
| 63 | cpld@3c00000 { |
||
| 64 | compatible = "lantiq,easy98000_addon"; |
||
| 65 | reg = <0x3c00000 0x2>; |
||
| 66 | }; |
||
| 67 | |||
| 68 | cpld@3c0000c { |
||
| 69 | compatible = "lantiq,easy98000_cpld_led"; |
||
| 70 | reg = <0x3c0000c 0x2>, <0x3c00012 0x2>; |
||
| 71 | }; |
||
| 72 | }; |
||
| 73 | |||
| 74 | /* // enable this for second uart: |
||
| 75 | &serial1 { |
||
| 76 | status = "okay"; |
||
| 77 | };*/ |
||
| 78 | |||
| 79 | &spi { |
||
| 80 | status = "okay"; |
||
| 81 | |||
| 82 | eeprom@1 { |
||
| 83 | compatible = "atmel,at25", "atmel,at25160n"; |
||
| 84 | reg = <2>; |
||
| 85 | spi-max-frequency = <1000000>; |
||
| 86 | spi-cpha; |
||
| 87 | spi-cpol; |
||
| 88 | |||
| 89 | pagesize = <32>; |
||
| 90 | size = <2048>; |
||
| 91 | address-width = <16>; |
||
| 92 | }; |
||
| 93 | }; |
||
| 94 | |||
| 95 | &i2c { |
||
| 96 | status = "okay"; |
||
| 97 | |||
| 98 | clock-frequency = <100000>; |
||
| 99 | |||
| 100 | /* eeprom-emulation by OMU */ |
||
| 101 | eeprom@50 { |
||
| 102 | compatible = "at,24c02"; |
||
| 103 | reg = <0x50>; |
||
| 104 | }; |
||
| 105 | eeprom@51 { |
||
| 106 | compatible = "at,24c02"; |
||
| 107 | reg = <0x51>; |
||
| 108 | }; |
||
| 109 | }; |
||
| 110 |