OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3050.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "netgear,wnce2001", "ralink,rt3052-soc"; |
||
10 | model = "Netgear WNCE2001"; |
||
11 | |||
12 | chosen { |
||
13 | bootargs = "console=ttyS0,115200"; |
||
14 | }; |
||
15 | |||
3 | office | 16 | gpio-leds { |
1 | office | 17 | compatible = "gpio-leds"; |
18 | |||
3 | office | 19 | power-green { |
1 | office | 20 | label = "wnce2001:green:power"; |
21 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
||
22 | }; |
||
23 | |||
24 | power-red { |
||
25 | label = "wnce2001:red:power"; |
||
26 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
27 | }; |
||
28 | |||
29 | wlan-green { |
||
30 | label = "wnce2001:green:wlan"; |
||
31 | gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; |
||
32 | }; |
||
33 | |||
34 | wlan-red { |
||
35 | label = "wnce2001:red:wlan"; |
||
36 | gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; |
||
37 | }; |
||
38 | }; |
||
39 | |||
3 | office | 40 | gpio-keys-polled { |
1 | office | 41 | compatible = "gpio-keys-polled"; |
3 | office | 42 | #address-cells = <1>; |
43 | #size-cells = <0>; |
||
1 | office | 44 | poll-interval = <20>; |
45 | |||
46 | reset { |
||
47 | label = "reset"; |
||
48 | gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
||
49 | linux,code = <KEY_RESTART>; |
||
50 | }; |
||
51 | |||
52 | wps { |
||
53 | label = "wps"; |
||
54 | gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
||
55 | linux,code = <KEY_WPS_BUTTON>; |
||
56 | }; |
||
57 | |||
58 | rt { |
||
59 | label = "rt"; |
||
60 | gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
||
61 | linux,code = <BTN_0>; |
||
62 | }; |
||
63 | |||
64 | ap { |
||
65 | label = "ap"; |
||
66 | gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; |
||
67 | linux,code = <BTN_1>; |
||
68 | }; |
||
69 | }; |
||
70 | }; |
||
71 | |||
72 | &spi0 { |
||
73 | status = "okay"; |
||
74 | |||
75 | m25p80@0 { |
||
3 | office | 76 | #address-cells = <1>; |
77 | #size-cells = <1>; |
||
1 | office | 78 | compatible = "jedec,spi-nor"; |
79 | reg = <0>; |
||
80 | spi-max-frequency = <10000000>; |
||
81 | |||
3 | office | 82 | partition@0 { |
83 | label = "u-boot"; |
||
84 | reg = <0x0 0x30000>; |
||
85 | read-only; |
||
86 | }; |
||
1 | office | 87 | |
3 | office | 88 | factory: partition@30000 { |
89 | label = "factory"; |
||
90 | reg = <0x30000 0x10000>; |
||
91 | read-only; |
||
92 | }; |
||
1 | office | 93 | |
3 | office | 94 | partition@40000 { |
95 | label = "config"; |
||
96 | reg = <0x40000 0x20000>; |
||
97 | read-only; |
||
98 | }; |
||
1 | office | 99 | |
3 | office | 100 | partition@60000 { |
101 | label = "language"; |
||
102 | reg = <0x60000 0x30000>; |
||
103 | read-only; |
||
104 | }; |
||
1 | office | 105 | |
3 | office | 106 | partition@90000 { |
107 | label = "pot"; |
||
108 | reg = <0x90000 0x10000>; |
||
109 | read-only; |
||
110 | }; |
||
1 | office | 111 | |
3 | office | 112 | partition@a0000 { |
113 | label = "checksum"; |
||
114 | reg = <0xa0000 0x10000>; |
||
115 | }; |
||
1 | office | 116 | |
3 | office | 117 | partition@b0000 { |
118 | label = "firmware"; |
||
119 | reg = <0xb0000 0x350000>; |
||
1 | office | 120 | }; |
121 | }; |
||
122 | }; |
||
123 | |||
124 | &pinctrl { |
||
125 | state_default: pinctrl0 { |
||
126 | gpio { |
||
127 | ralink,group = "i2c", "jtag", "rgmii", "mdio", "uartf"; |
||
128 | ralink,function = "gpio"; |
||
129 | }; |
||
130 | }; |
||
131 | }; |
||
132 | |||
133 | ðernet { |
||
134 | mtd-mac-address = <&factory 0x28>; |
||
135 | }; |
||
136 | |||
137 | &wmac { |
||
138 | ralink,mtd-eeprom = <&factory 0>; |
||
139 | }; |