OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3883.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "sitecom,wlr-6000", "ralink,rt3883-soc"; |
||
10 | model = "Sitecom WLR-6000"; |
||
11 | |||
3 | office | 12 | gpio-keys-polled { |
1 | office | 13 | compatible = "gpio-keys-polled"; |
3 | office | 14 | #address-cells = <1>; |
15 | #size-cells = <0>; |
||
1 | office | 16 | poll-interval = <20>; |
17 | |||
18 | reset { |
||
19 | label = "reset"; |
||
20 | gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; |
||
21 | linux,code = <KEY_RESTART>; |
||
22 | }; |
||
23 | }; |
||
24 | |||
3 | office | 25 | gpio-leds { |
1 | office | 26 | compatible = "gpio-leds"; |
27 | |||
3 | office | 28 | power { |
1 | office | 29 | label = "wlr-6000:red:power"; |
30 | gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
||
31 | }; |
||
32 | |||
33 | ops { |
||
34 | label = "wlr-6000:white:ops"; |
||
35 | gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
||
36 | }; |
||
37 | }; |
||
38 | |||
39 | gpio_export { |
||
40 | compatible = "gpio-export"; |
||
41 | #size-cells = <0>; |
||
42 | |||
43 | usb { |
||
44 | gpio-export,name = "usb"; |
||
45 | gpio-export,output = <1>; |
||
46 | gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; |
||
47 | }; |
||
48 | }; |
||
49 | }; |
||
50 | |||
51 | &gpio1 { |
||
52 | status = "okay"; |
||
53 | }; |
||
54 | |||
55 | &pinctrl { |
||
56 | state_default: pinctrl0 { |
||
57 | gpio { |
||
58 | ralink,group = "i2c", "jtag", "uartf"; |
||
59 | ralink,function = "gpio"; |
||
60 | }; |
||
61 | }; |
||
62 | }; |
||
63 | |||
64 | ðernet { |
||
65 | status = "okay"; |
||
66 | mtd-mac-address = <&factory 0x8004>; |
||
67 | mtd-mac-address-increment = <1>; |
||
68 | |||
69 | port@0 { |
||
70 | phy-handle = <&phy0>; |
||
71 | phy-mode = "rgmii"; |
||
72 | }; |
||
73 | |||
74 | mdio-bus { |
||
75 | status = "okay"; |
||
76 | |||
77 | phy0: ethernet-phy@0 { |
||
78 | reg = <0>; |
||
79 | phy-mode = "rgmii"; |
||
80 | |||
81 | qca,ar8327-initvals = < |
||
82 | 0x04 0x07600000 /* PORT0 PAD MODE CTRL */ |
||
83 | 0x0c 0x07600000 /* PORT6 PAD MODE CTRL */ |
||
84 | 0x10 0x40000000 /* Power-on Strapping: 176-pin interface configuration */ |
||
85 | 0x50 0xc437c437 /* LED Control Register 0 */ |
||
86 | 0x54 0xc337c337 /* LED Control Register 1 */ |
||
87 | 0x58 0x00000000 /* LED Control Register 2 */ |
||
88 | 0x5c 0x03ffff00 /* LED Control Register 3 */ |
||
89 | 0x7c 0x0000007e /* PORT0_STATUS */ |
||
90 | 0x94 0x0000007e /* PORT6 STATUS */ |
||
91 | >; |
||
92 | }; |
||
93 | }; |
||
94 | }; |
||
95 | |||
96 | &spi0 { |
||
97 | status = "okay"; |
||
98 | |||
99 | m25p80@0 { |
||
3 | office | 100 | #address-cells = <1>; |
101 | #size-cells = <1>; |
||
1 | office | 102 | compatible = "jedec,spi-nor"; |
103 | reg = <0>; |
||
104 | spi-max-frequency = <8600000>; |
||
105 | m25p,fast-read; |
||
106 | |||
3 | office | 107 | partition@0 { |
108 | label = "u-boot"; |
||
109 | reg = <0x0 0x30000>; |
||
110 | read-only; |
||
111 | }; |
||
1 | office | 112 | |
3 | office | 113 | partition@30000 { |
114 | label = "u-boot-env"; |
||
115 | reg = <0x30000 0x10000>; |
||
116 | read-only; |
||
117 | }; |
||
1 | office | 118 | |
3 | office | 119 | factory: partition@40000 { |
120 | label = "factory"; |
||
121 | reg = <0x40000 0x10000>; |
||
122 | read-only; |
||
123 | }; |
||
1 | office | 124 | |
3 | office | 125 | partition@50000 { |
126 | label = "firmware"; |
||
127 | reg = <0x50000 0x713000>; |
||
128 | }; |
||
1 | office | 129 | |
3 | office | 130 | partition@763000 { |
131 | label = "manufacture"; |
||
132 | reg = <0x763000 0x7D000>; |
||
133 | read-only; |
||
134 | }; |
||
1 | office | 135 | |
3 | office | 136 | partition@7E0000 { |
137 | label = "backup"; |
||
138 | reg = <0x7E0000 0x10000>; |
||
139 | read-only; |
||
140 | }; |
||
1 | office | 141 | |
3 | office | 142 | partition@7F0000 { |
143 | label = "storage"; |
||
144 | reg = <0x7F0000 0x10000>; |
||
145 | read-only; |
||
1 | office | 146 | }; |
147 | }; |
||
148 | }; |
||
149 | |||
150 | &pci { |
||
151 | status = "okay"; |
||
3 | office | 152 | pinctrl-names = "default"; |
153 | pinctrl-0 = <&pci_pins>; |
||
1 | office | 154 | |
3 | office | 155 | pci_pins: pci { |
156 | pci { |
||
157 | ralink,group = "pci"; |
||
158 | ralink,function = "pci-fnc"; |
||
159 | }; |
||
160 | }; |
||
1 | office | 161 | |
3 | office | 162 | host-bridge { |
163 | pci-bridge@1 { |
||
164 | status = "okay"; |
||
165 | |||
166 | wifi@1814,3091 { |
||
167 | compatible = "pci1814,3091"; |
||
168 | reg = <0x10000 0 0 0 0>; |
||
169 | ralink,mtd-eeprom = <&factory 0x8000>; |
||
170 | }; |
||
171 | }; |
||
1 | office | 172 | }; |
173 | }; |
||
174 | |||
175 | &wmac { |
||
176 | status = "okay"; |
||
177 | ralink,2ghz = <0>; |
||
178 | ralink,mtd-eeprom = <&factory 0x0>; |
||
179 | }; |
||
180 | |||
181 | &ehci { |
||
182 | status = "okay"; |
||
183 | }; |
||
184 | |||
185 | &ohci { |
||
186 | status = "okay"; |
||
187 | }; |