OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3050.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "sitecom,wl-351", "ralink,rt3052-soc"; |
||
10 | model = "Sitecom WL-351 v1 002"; |
||
11 | |||
12 | aliases { |
||
13 | led-boot = &led_power; |
||
14 | led-failsafe = &led_power; |
||
15 | led-running = &led_power; |
||
16 | led-upgrade = &led_power; |
||
17 | }; |
||
18 | |||
19 | cfi@1f000000 { |
||
20 | compatible = "cfi-flash"; |
||
21 | reg = <0x1f000000 0x800000>; |
||
22 | bank-width = <2>; |
||
23 | device-width = <2>; |
||
24 | |||
25 | partitions { |
||
26 | compatible = "fixed-partitions"; |
||
27 | #address-cells = <1>; |
||
28 | #size-cells = <1>; |
||
29 | |||
30 | partition@0 { |
||
31 | label = "u-boot"; |
||
32 | reg = <0x0 0x30000>; |
||
33 | read-only; |
||
34 | }; |
||
35 | |||
36 | partition@30000 { |
||
37 | label = "u-boot-env"; |
||
38 | reg = <0x30000 0x10000>; |
||
39 | read-only; |
||
40 | }; |
||
41 | |||
42 | factory: partition@40000 { |
||
43 | label = "factory"; |
||
44 | reg = <0x40000 0x10000>; |
||
45 | read-only; |
||
46 | }; |
||
47 | |||
48 | partition@50000 { |
||
49 | compatible = "denx,uimage"; |
||
50 | label = "firmware"; |
||
51 | reg = <0x50000 0x3b0000>; |
||
52 | }; |
||
53 | }; |
||
54 | }; |
||
55 | |||
56 | leds { |
||
57 | compatible = "gpio-leds"; |
||
58 | |||
59 | led_power: power { |
||
60 | label = "wl-351:amber:power"; |
||
61 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
||
62 | }; |
||
63 | |||
64 | unpopulated { |
||
65 | label = "wl-351:amber:unpopulated"; |
||
66 | gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
||
67 | }; |
||
68 | |||
69 | unpopulated2 { |
||
70 | label = "wl-351:blue:unpopulated"; |
||
71 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
||
72 | }; |
||
73 | }; |
||
74 | |||
75 | keys { |
||
76 | compatible = "gpio-keys-polled"; |
||
77 | poll-interval = <20>; |
||
78 | |||
79 | reset { |
||
80 | label = "reset"; |
||
81 | gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
||
82 | linux,code = <KEY_RESTART>; |
||
83 | }; |
||
84 | |||
85 | wps { |
||
86 | label = "wps"; |
||
87 | gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
||
88 | linux,code = <KEY_WPS_BUTTON>; |
||
89 | }; |
||
90 | }; |
||
91 | |||
92 | rtl8366rb { |
||
93 | compatible = "realtek,rtl8366rb"; |
||
94 | gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>; |
||
95 | gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
||
96 | }; |
||
97 | }; |
||
98 | |||
99 | &pinctrl { |
||
100 | state_default: pinctrl0 { |
||
101 | gpio { |
||
102 | ralink,group = "spi", "i2c", "jtag", "mdio", "uartf"; |
||
103 | ralink,function = "gpio"; |
||
104 | }; |
||
105 | }; |
||
106 | }; |
||
107 | |||
108 | ðernet { |
||
109 | mtd-mac-address = <&factory 0x4>; |
||
110 | pinctrl-names = "default"; |
||
111 | pinctrl-0 = <&rgmii_pins>; |
||
112 | }; |
||
113 | |||
114 | &esw { |
||
115 | ralink,rgmii = <1>; |
||
116 | mediatek,portmap = <0x3f>; |
||
117 | ralink,fct2 = <0x0002500c>; |
||
118 | /* |
||
119 | * ext phy base addr 31, rx/tx clock skew 0, |
||
120 | * turbo mii off, rgmi 3.3v off, port 5 polling off |
||
121 | * port5: enabled, gige, full-duplex, rx/tx-flow-control |
||
122 | * port6: enabled, gige, full-duplex, rx/tx-flow-control |
||
123 | */ |
||
124 | ralink,fpa2 = <0x1f003fff>; |
||
125 | }; |
||
126 | |||
127 | &wmac { |
||
128 | ralink,mtd-eeprom = <&factory 0>; |
||
129 | }; |
||
130 | |||
131 | &otg { |
||
132 | status = "okay"; |
||
133 | }; |