OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt5350.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "wiznet,wizfi630a", "ralink,rt5350-soc"; |
||
10 | model = "WIZnet WizFi630A"; |
||
11 | |||
12 | chosen { |
||
13 | bootargs = "console=ttyS1,115200"; |
||
14 | }; |
||
15 | |||
3 | office | 16 | gpio-leds { |
1 | office | 17 | compatible = "gpio-leds"; |
18 | |||
3 | office | 19 | run { |
1 | office | 20 | label = "wizfi630a::run"; |
21 | gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
||
22 | }; |
||
23 | |||
24 | wps { |
||
25 | label = "wizfi630a::wps"; |
||
26 | gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; |
||
27 | }; |
||
28 | |||
29 | uart1 { |
||
30 | label = "wizfi630a::uart1"; |
||
31 | gpios = <&gpio0 18 GPIO_ACTIVE_LOW>; |
||
32 | }; |
||
33 | |||
34 | uart2 { |
||
35 | label = "wizfi630a::uart2"; |
||
36 | gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; |
||
37 | }; |
||
38 | }; |
||
39 | |||
3 | office | 40 | gpio-keys-polled { |
1 | office | 41 | compatible = "gpio-keys-polled"; |
3 | office | 42 | #address-cells = <1>; |
43 | #size-cells = <0>; |
||
1 | office | 44 | poll-interval = <20>; |
45 | |||
46 | reset { |
||
47 | label = "reset"; |
||
48 | gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; |
||
49 | linux,code = <KEY_RESTART>; |
||
50 | }; |
||
51 | |||
52 | wps { |
||
53 | label = "wps"; |
||
54 | gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
||
55 | linux,code = <KEY_WPS_BUTTON>; |
||
56 | }; |
||
3 | office | 57 | |
1 | office | 58 | scm1 { |
59 | label = "SCM1"; |
||
60 | gpios = <&gpio0 19 GPIO_ACTIVE_LOW>; |
||
61 | linux,code = <BTN_0>; |
||
62 | }; |
||
63 | |||
64 | scm2 { |
||
65 | label = "SCM2"; |
||
66 | gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
||
67 | linux,code = <BTN_1>; |
||
68 | }; |
||
69 | }; |
||
70 | }; |
||
71 | |||
72 | &gpio1 { |
||
73 | status = "okay"; |
||
74 | }; |
||
75 | |||
76 | &spi0 { |
||
77 | status = "okay"; |
||
78 | |||
79 | m25p80@0 { |
||
3 | office | 80 | #address-cells = <1>; |
81 | #size-cells = <1>; |
||
1 | office | 82 | compatible = "jedec,spi-nor"; |
83 | reg = <0>; |
||
84 | spi-max-frequency = <10000000>; |
||
85 | |||
3 | office | 86 | partition@0 { |
1 | office | 87 | #size-cells = <1>; |
3 | office | 88 | label = "uboot"; |
89 | reg = <0x0 0x30000>; |
||
90 | read-only; |
||
91 | }; |
||
1 | office | 92 | |
3 | office | 93 | partition@30000 { |
94 | #size-cells = <1>; |
||
95 | label = "uboot-env"; |
||
96 | reg = <0x30000 0x10000>; |
||
97 | read-only; |
||
98 | }; |
||
1 | office | 99 | |
3 | office | 100 | factory: partition@40000 { |
101 | #size-cells = <1>; |
||
102 | label = "factory"; |
||
103 | reg = <0x40000 0x10000>; |
||
104 | read-only; |
||
105 | }; |
||
1 | office | 106 | |
3 | office | 107 | partition@50000 { |
108 | #size-cells = <1>; |
||
109 | label = "firmware"; |
||
110 | reg = <0x50000 0xfb0000>; |
||
1 | office | 111 | }; |
112 | }; |
||
113 | }; |
||
114 | |||
115 | &uart { |
||
116 | status = "okay"; |
||
117 | pinctrl-names = "default"; |
||
118 | pinctrl-0 = <&uartf_pins>; |
||
119 | }; |
||
120 | |||
121 | &pinctrl { |
||
122 | state_default: pinctrl0 { |
||
123 | gpio { |
||
124 | ralink,group = "i2c", "jtag" ; |
||
125 | ralink,function = "gpio"; |
||
126 | }; |
||
127 | }; |
||
128 | }; |
||
129 | |||
130 | ðernet { |
||
131 | mtd-mac-address = <&factory 0x4>; |
||
132 | }; |
||
133 | |||
134 | &esw { |
||
135 | mediatek,portmap = <0x17>; |
||
136 | }; |
||
137 | |||
138 | &wmac { |
||
139 | ralink,mtd-eeprom = <&factory 0>; |
||
140 | }; |
||
141 | |||
142 | &ehci { |
||
143 | status = "okay"; |
||
144 | }; |
||
145 | |||
146 | &ohci { |
||
147 | status = "okay"; |
||
148 | }; |