OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "mt7620a.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "buffalo,whr-300hp2", "ralink,mt7620a-soc"; |
||
10 | model = "Buffalo WHR-300HP2"; |
||
11 | |||
3 | office | 12 | gpio-leds { |
1 | office | 13 | compatible = "gpio-leds"; |
14 | |||
15 | power { |
||
16 | label = "whr-300hp2:red:power"; |
||
17 | gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; |
||
18 | }; |
||
19 | |||
20 | wifi { |
||
21 | label = "whr-300hp2:green:wifi"; |
||
22 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
||
23 | }; |
||
24 | |||
3 | office | 25 | power2 { |
1 | office | 26 | label = "whr-300hp2:green:power"; |
27 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
28 | }; |
||
29 | |||
30 | wifi2 { |
||
31 | label = "whr-300hp2:orange:wifi"; |
||
32 | gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
||
33 | }; |
||
34 | |||
35 | internet { |
||
36 | label = "whr-300hp2:green:internet"; |
||
37 | gpios = <&gpio2 17 GPIO_ACTIVE_LOW>; |
||
38 | }; |
||
39 | |||
40 | router { |
||
41 | label = "whr-300hp2:green:router"; |
||
42 | gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; |
||
43 | }; |
||
44 | |||
45 | router2 { |
||
46 | label = "whr-300hp2:orange:router"; |
||
47 | gpios = <&gpio2 19 GPIO_ACTIVE_LOW>; |
||
48 | }; |
||
49 | }; |
||
50 | |||
3 | office | 51 | gpio-keys-polled { |
1 | office | 52 | compatible = "gpio-keys-polled"; |
3 | office | 53 | #address-cells = <1>; |
54 | #size-cells = <0>; |
||
1 | office | 55 | poll-interval = <20>; |
56 | |||
57 | reset { |
||
58 | label = "reset"; |
||
59 | gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; |
||
60 | linux,code = <KEY_RESTART>; |
||
61 | }; |
||
62 | |||
63 | aoss { |
||
64 | label = "aoss"; |
||
65 | gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; |
||
66 | linux,code = <KEY_WPS_BUTTON>; |
||
67 | }; |
||
68 | |||
69 | ap { |
||
70 | label = "ap"; |
||
71 | gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; |
||
72 | linux,code = <BTN_0>; |
||
73 | linux,input-type = <EV_SW>; |
||
74 | }; |
||
75 | |||
76 | bridge { |
||
77 | label = "bridge"; |
||
78 | gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; |
||
79 | linux,code = <BTN_0>; |
||
80 | linux,input-type = <EV_SW>; |
||
81 | }; |
||
82 | }; |
||
83 | }; |
||
84 | |||
85 | &gpio2 { |
||
86 | status = "okay"; |
||
87 | }; |
||
88 | |||
89 | &spi0 { |
||
90 | status = "okay"; |
||
91 | |||
92 | m25p80@0 { |
||
3 | office | 93 | #address-cells = <1>; |
94 | #size-cells = <1>; |
||
1 | office | 95 | compatible = "jedec,spi-nor"; |
96 | reg = <0>; |
||
97 | spi-max-frequency = <10000000>; |
||
98 | |||
3 | office | 99 | partition@0 { |
100 | label = "u-boot"; |
||
101 | reg = <0x0 0x30000>; |
||
102 | read-only; |
||
103 | }; |
||
1 | office | 104 | |
3 | office | 105 | partition@30000 { |
106 | label = "u-boot-env"; |
||
107 | reg = <0x30000 0x10000>; |
||
108 | read-only; |
||
109 | }; |
||
1 | office | 110 | |
3 | office | 111 | factory: partition@40000 { |
112 | label = "factory"; |
||
113 | reg = <0x40000 0x10000>; |
||
114 | read-only; |
||
115 | }; |
||
1 | office | 116 | |
3 | office | 117 | partition@50000 { |
118 | label = "firmware"; |
||
119 | reg = <0x50000 0x7b0000>; |
||
1 | office | 120 | }; |
121 | }; |
||
122 | }; |
||
123 | |||
124 | &pinctrl { |
||
125 | state_default: pinctrl0 { |
||
126 | gpio { |
||
127 | ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "wled", "nd_sd"; |
||
128 | ralink,function = "gpio"; |
||
129 | }; |
||
130 | }; |
||
131 | }; |
||
132 | |||
133 | ðernet { |
||
134 | pinctrl-names = "default"; |
||
135 | pinctrl-0 = <&ephy_pins>; |
||
136 | mediatek,portmap = "llllw"; |
||
137 | }; |
||
138 | |||
139 | &gsw { |
||
140 | mediatek,port4 = "ephy"; |
||
141 | }; |
||
142 | |||
143 | &wmac { |
||
144 | ralink,mtd-eeprom = <&factory 0>; |
||
145 | pinctrl-names = "default"; |
||
146 | pinctrl-0 = <&pa_pins>; |
||
147 | }; |