OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt2880.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | #address-cells = <1>; |
||
10 | #size-cells = <1>; |
||
11 | compatible = "asus,rt-n15", "ralink,rt2880-soc"; |
||
12 | model = "Asus RT-N15"; |
||
13 | |||
14 | aliases { |
||
15 | led-boot = &led_power; |
||
16 | led-failsafe = &led_power; |
||
17 | led-running = &led_power; |
||
18 | led-upgrade = &led_power; |
||
19 | }; |
||
20 | |||
21 | cfi@1f000000 { |
||
22 | compatible = "cfi-flash"; |
||
23 | reg = <0x1f000000 0x800000>; |
||
24 | bank-width = <2>; |
||
25 | device-width = <2>; |
||
26 | |||
27 | partitions { |
||
28 | compatible = "fixed-partitions"; |
||
29 | #address-cells = <1>; |
||
30 | #size-cells = <1>; |
||
31 | |||
32 | partition@0 { |
||
33 | label = "uboot"; |
||
34 | reg = <0x0 0x30000>; |
||
35 | read-only; |
||
36 | }; |
||
37 | |||
38 | partition@30000 { |
||
39 | label = "uboot-env"; |
||
40 | reg = <0x30000 0x10000>; |
||
41 | read-only; |
||
42 | }; |
||
43 | |||
44 | factory: partition@40000 { |
||
45 | label = "factory"; |
||
46 | reg = <0x40000 0x10000>; |
||
47 | read-only; |
||
48 | }; |
||
49 | |||
50 | partition@50000 { |
||
51 | compatible = "denx,uimage"; |
||
52 | label = "firmware"; |
||
53 | reg = <0x50000 0x3b0000>; |
||
54 | }; |
||
55 | }; |
||
56 | }; |
||
57 | |||
58 | rtl8366s { |
||
59 | compatible = "realtek,rtl8366s"; |
||
60 | gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>; |
||
61 | gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
||
62 | }; |
||
63 | |||
64 | keys { |
||
65 | compatible = "gpio-keys-polled"; |
||
66 | poll-interval = <100>; |
||
67 | |||
68 | wps { |
||
69 | label = "wps"; |
||
70 | gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; |
||
71 | linux,code = <KEY_WPS_BUTTON>; |
||
72 | }; |
||
73 | |||
74 | reset { |
||
75 | label = "reset"; |
||
76 | gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; |
||
77 | linux,code = <KEY_RESTART>; |
||
78 | }; |
||
79 | }; |
||
80 | |||
81 | leds { |
||
82 | compatible = "gpio-leds"; |
||
83 | |||
84 | led_power: power { |
||
85 | label = "rt-n15:blue:power"; |
||
86 | gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
||
87 | }; |
||
88 | }; |
||
89 | }; |
||
90 | |||
91 | &gpio0 { |
||
92 | status = "okay"; |
||
93 | }; |
||
94 | |||
95 | &pinctrl { |
||
96 | state_default: pinctrl0 { |
||
97 | gpio { |
||
98 | ralink,group = "i2c", "uartlite", "mdio"; |
||
99 | ralink,function = "gpio"; |
||
100 | }; |
||
101 | }; |
||
102 | }; |
||
103 | |||
104 | ðernet { |
||
105 | status = "okay"; |
||
106 | mtd-mac-address = <&factory 0x4>; |
||
107 | |||
108 | port@0 { |
||
109 | mediatek,fixed-link = <1000 1 1 1>; |
||
110 | }; |
||
111 | |||
112 | mdio-bus { |
||
113 | status = "okay"; |
||
114 | |||
115 | phy0: ethernet-phy@0 { |
||
116 | phy-mode = "mii"; |
||
117 | reg = <0>; |
||
118 | }; |
||
119 | }; |
||
120 | }; |
||
121 | |||
122 | &wmac { |
||
123 | ralink,mtd-eeprom = <&factory 0>; |
||
124 | }; |