OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt2880.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | #address-cells = <1>; |
||
10 | #size-cells = <1>; |
||
11 | compatible = "asus,rt-n15", "ralink,rt2880-soc"; |
||
12 | model = "Asus RT-N15"; |
||
13 | |||
14 | cfi@1f000000 { |
||
15 | compatible = "cfi-flash"; |
||
16 | reg = <0x1f000000 0x800000>; |
||
17 | bank-width = <2>; |
||
18 | device-width = <2>; |
||
3 | office | 19 | #address-cells = <1>; |
20 | #size-cells = <1>; |
||
1 | office | 21 | |
3 | office | 22 | partition@0 { |
23 | label = "uboot"; |
||
24 | reg = <0x0 0x30000>; |
||
25 | read-only; |
||
26 | }; |
||
1 | office | 27 | |
3 | office | 28 | partition@30000 { |
29 | label = "uboot-env"; |
||
30 | reg = <0x30000 0x10000>; |
||
31 | read-only; |
||
32 | }; |
||
1 | office | 33 | |
3 | office | 34 | factory: partition@40000 { |
35 | label = "factory"; |
||
36 | reg = <0x40000 0x10000>; |
||
37 | read-only; |
||
38 | }; |
||
1 | office | 39 | |
3 | office | 40 | partition@50000 { |
41 | label = "firmware"; |
||
42 | reg = <0x50000 0x3b0000>; |
||
1 | office | 43 | }; |
44 | }; |
||
45 | |||
46 | rtl8366s { |
||
47 | compatible = "realtek,rtl8366s"; |
||
48 | gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>; |
||
49 | gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
||
50 | }; |
||
51 | |||
3 | office | 52 | gpio-keys-polled { |
1 | office | 53 | compatible = "gpio-keys-polled"; |
3 | office | 54 | #address-cells = <1>; |
55 | #size-cells = <0>; |
||
1 | office | 56 | poll-interval = <100>; |
57 | |||
58 | wps { |
||
59 | label = "wps"; |
||
60 | gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; |
||
61 | linux,code = <KEY_WPS_BUTTON>; |
||
62 | }; |
||
63 | |||
64 | reset { |
||
65 | label = "reset"; |
||
66 | gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; |
||
67 | linux,code = <KEY_RESTART>; |
||
68 | }; |
||
69 | }; |
||
70 | |||
3 | office | 71 | gpio-leds { |
1 | office | 72 | compatible = "gpio-leds"; |
73 | |||
3 | office | 74 | power { |
1 | office | 75 | label = "rt-n15:blue:power"; |
76 | gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
||
77 | }; |
||
78 | }; |
||
79 | }; |
||
80 | |||
81 | &gpio0 { |
||
82 | status = "okay"; |
||
83 | }; |
||
84 | |||
85 | &pinctrl { |
||
86 | state_default: pinctrl0 { |
||
87 | gpio { |
||
88 | ralink,group = "i2c", "uartlite", "mdio"; |
||
89 | ralink,function = "gpio"; |
||
90 | }; |
||
91 | }; |
||
92 | }; |
||
93 | |||
94 | ðernet { |
||
95 | status = "okay"; |
||
96 | mtd-mac-address = <&factory 0x4>; |
||
97 | |||
98 | port@0 { |
||
99 | mediatek,fixed-link = <1000 1 1 1>; |
||
100 | }; |
||
101 | |||
102 | mdio-bus { |
||
103 | status = "okay"; |
||
104 | |||
105 | phy0: ethernet-phy@0 { |
||
106 | phy-mode = "mii"; |
||
107 | reg = <0>; |
||
108 | }; |
||
109 | }; |
||
110 | }; |
||
111 | |||
112 | &wmac { |
||
113 | ralink,mtd-eeprom = <&factory 0>; |
||
114 | }; |