OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "mt7620a.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "phicomm,k2g", "ralink,mt7620a-soc"; |
||
10 | model = "Phicomm K2G"; |
||
11 | |||
12 | aliases { |
||
13 | led-boot = &led_blue; |
||
14 | led-failsafe = &led_blue; |
||
15 | led-running = &led_blue; |
||
16 | led-upgrade = &led_blue; |
||
17 | serial0 = &uartlite; |
||
18 | }; |
||
19 | |||
20 | leds { |
||
21 | compatible = "gpio-leds"; |
||
22 | |||
23 | led_blue: blue { |
||
24 | label = "k2g:blue:status"; |
||
25 | gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
||
26 | }; |
||
27 | |||
28 | yellow { |
||
29 | label = "k2g:yellow:status"; |
||
30 | gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
||
31 | }; |
||
32 | |||
33 | red { |
||
34 | label = "k2g:red:status"; |
||
35 | gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; |
||
36 | }; |
||
37 | }; |
||
38 | |||
39 | keys { |
||
40 | compatible = "gpio-keys-polled"; |
||
41 | poll-interval = <20>; |
||
42 | |||
43 | reset { |
||
44 | label = "reset"; |
||
45 | gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
||
46 | linux,code = <KEY_RESTART>; |
||
47 | }; |
||
48 | }; |
||
49 | }; |
||
50 | |||
51 | &spi0 { |
||
52 | status = "okay"; |
||
53 | |||
54 | m25p80@0 { |
||
55 | compatible = "jedec,spi-nor"; |
||
56 | reg = <0>; |
||
57 | spi-max-frequency = <24000000>; |
||
58 | |||
59 | partitions { |
||
60 | compatible = "fixed-partitions"; |
||
61 | #address-cells = <1>; |
||
62 | #size-cells = <1>; |
||
63 | |||
64 | partition@0 { |
||
65 | reg = <0x0 0x30000>; |
||
66 | label = "u-boot"; |
||
67 | read-only; |
||
68 | }; |
||
69 | |||
70 | partition@30000 { |
||
71 | reg = <0x30000 0x10000>; |
||
72 | label = "u-boot-env"; |
||
73 | read-only; |
||
74 | }; |
||
75 | |||
76 | factory: partition@40000 { |
||
77 | reg = <0x40000 0x10000>; |
||
78 | label = "factory"; |
||
79 | read-only; |
||
80 | }; |
||
81 | |||
82 | partition@50000 { |
||
83 | reg = <0x50000 0x50000>; |
||
84 | label = "permanent_config"; |
||
85 | read-only; |
||
86 | }; |
||
87 | |||
88 | partition@a0000 { |
||
89 | compatible = "denx,uimage"; |
||
90 | reg = <0xa0000 0x760000>; |
||
91 | label = "firmware"; |
||
92 | }; |
||
93 | }; |
||
94 | }; |
||
95 | }; |
||
96 | |||
97 | &pinctrl { |
||
98 | state_default: pinctrl0 { |
||
99 | gpio { |
||
100 | ralink,group = "i2c", "uartf"; |
||
101 | ralink,function = "gpio"; |
||
102 | }; |
||
103 | }; |
||
104 | }; |
||
105 | |||
106 | ðernet { |
||
107 | pinctrl-names = "default"; |
||
108 | pinctrl-0 = <&rgmii2_pins &mdio_pins>; |
||
109 | mtd-mac-address = <&factory 0x28>; |
||
110 | mediatek,portmap = "llllw"; |
||
111 | |||
112 | port@5 { |
||
113 | status = "okay"; |
||
114 | phy-handle = <&phy5>; |
||
115 | phy-mode = "rgmii"; |
||
116 | }; |
||
117 | |||
118 | mdio-bus { |
||
119 | status = "okay"; |
||
120 | |||
121 | phy5: ethernet-phy@5 { |
||
122 | reg = <5>; |
||
123 | phy-mode = "rgmii"; |
||
124 | }; |
||
125 | }; |
||
126 | }; |
||
127 | |||
128 | &pcie { |
||
129 | status = "okay"; |
||
130 | }; |
||
131 | |||
132 | &pcie0 { |
||
133 | mt76@0,0 { |
||
134 | reg = <0x0000 0 0 0 0>; |
||
135 | mediatek,mtd-eeprom = <&factory 0x8000>; |
||
136 | ieee80211-freq-limit = <5000000 6000000>; |
||
137 | }; |
||
138 | }; |
||
139 | |||
140 | &wmac { |
||
141 | ralink,mtd-eeprom = <&factory 0>; |
||
142 | pinctrl-names = "default"; |
||
143 | pinctrl-0 = <&pa_pins>; |
||
144 | }; |