OpenWrt – Blame information for rev 3

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 /dts-v1/;
2  
3 #include "mt7620a.dtsi"
4  
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/input.h>
7  
8 / {
9 compatible = "phicomm,k2g", "ralink,mt7620a-soc";
10 model = "Phicomm K2G";
11  
12 aliases {
13 serial0 = &uartlite;
14 };
15  
3 office 16 gpio-leds {
1 office 17 compatible = "gpio-leds";
18  
19 led_blue: blue {
20 label = "k2g:blue:status";
21 gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
22 };
23  
24 yellow {
25 label = "k2g:yellow:status";
26 gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
27 };
28  
29 red {
30 label = "k2g:red:status";
31 gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
32 };
33 };
34  
3 office 35 gpio-keys-polled {
1 office 36 compatible = "gpio-keys-polled";
3 office 37 #address-cells = <1>;
38 #size-cells = <0>;
1 office 39 poll-interval = <20>;
40  
41 reset {
42 label = "reset";
43 gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
44 linux,code = <KEY_RESTART>;
45 };
46 };
47 };
48  
49 &spi0 {
50 status = "okay";
51  
52 m25p80@0 {
3 office 53 #address-cells = <1>;
54 #size-cells = <1>;
1 office 55 compatible = "jedec,spi-nor";
56 reg = <0>;
57 spi-max-frequency = <24000000>;
58  
59 partitions {
60 compatible = "fixed-partitions";
61 #address-cells = <1>;
62 #size-cells = <1>;
63  
3 office 64 u-boot@0 {
1 office 65 reg = <0x0 0x30000>;
66 read-only;
67 };
68  
3 office 69 u-boot-env@30000 {
1 office 70 reg = <0x30000 0x10000>;
71 read-only;
72 };
73  
3 office 74 factory: factory@40000 {
1 office 75 reg = <0x40000 0x10000>;
76 read-only;
77 };
78  
3 office 79 permanent_config@50000 {
1 office 80 reg = <0x50000 0x50000>;
81 read-only;
82 };
83  
3 office 84 firmware@a0000 {
1 office 85 reg = <0xa0000 0x760000>;
86 };
87 };
88 };
89 };
90  
91 &pinctrl {
92 state_default: pinctrl0 {
93 gpio {
94 ralink,group = "i2c", "uartf";
95 ralink,function = "gpio";
96 };
97 };
98 };
99  
100 &ethernet {
101 pinctrl-names = "default";
102 pinctrl-0 = <&rgmii2_pins &mdio_pins>;
103 mtd-mac-address = <&factory 0x28>;
104 mediatek,portmap = "llllw";
105  
106 port@5 {
107 status = "okay";
108 phy-handle = <&phy5>;
109 phy-mode = "rgmii";
110 };
111  
112 mdio-bus {
113 status = "okay";
114  
115 phy5: ethernet-phy@5 {
116 reg = <5>;
117 phy-mode = "rgmii";
118 };
119 };
120 };
121  
122 &pcie {
123 status = "okay";
124  
3 office 125 pcie-bridge {
126 mt76@0,0 {
127 reg = <0x0000 0 0 0 0>;
128 device_type = "pci";
129 mediatek,mtd-eeprom = <&factory 0x8000>;
130 ieee80211-freq-limit = <5000000 6000000>;
131 };
1 office 132 };
133 };
134  
135 &wmac {
136 ralink,mtd-eeprom = <&factory 0>;
137 pinctrl-names = "default";
138 pinctrl-0 = <&pa_pins>;
139 };