OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3050.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "jcg,jhr-n926r", "ralink,rt3052-soc"; |
||
10 | model = "JCG JHR-N926R"; |
||
11 | |||
12 | cfi@1f000000 { |
||
13 | compatible = "cfi-flash"; |
||
14 | reg = <0x1f000000 0x800000>; |
||
15 | bank-width = <2>; |
||
16 | device-width = <2>; |
||
3 | office | 17 | #address-cells = <1>; |
18 | #size-cells = <1>; |
||
1 | office | 19 | |
3 | office | 20 | partition@0 { |
21 | label = "u-boot"; |
||
22 | reg = <0x0 0x30000>; |
||
23 | read-only; |
||
24 | }; |
||
1 | office | 25 | |
3 | office | 26 | partition@30000 { |
27 | label = "u-boot-env"; |
||
28 | reg = <0x30000 0x10000>; |
||
29 | read-only; |
||
30 | }; |
||
1 | office | 31 | |
3 | office | 32 | factory: partition@40000 { |
33 | label = "factory"; |
||
34 | reg = <0x40000 0x10000>; |
||
35 | read-only; |
||
36 | }; |
||
1 | office | 37 | |
3 | office | 38 | partition@50000 { |
39 | label = "firmware"; |
||
40 | reg = <0x50000 0x3b0000>; |
||
1 | office | 41 | }; |
42 | }; |
||
43 | |||
3 | office | 44 | gpio-leds { |
1 | office | 45 | compatible = "gpio-leds"; |
46 | |||
47 | wlan1 { |
||
48 | label = "jhr-n926r:red:wlan"; |
||
49 | gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; |
||
50 | }; |
||
51 | |||
52 | wlan2 { |
||
53 | label = "jhr-n926r:yellow:wlan"; |
||
54 | gpios = <&gpio0 19 GPIO_ACTIVE_LOW>; |
||
55 | }; |
||
56 | |||
57 | wlan3 { |
||
58 | label = "jhr-n926r:green:wlan"; |
||
59 | gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; |
||
60 | }; |
||
61 | |||
3 | office | 62 | system { |
1 | office | 63 | label = "jhr-n926r:blue:system"; |
64 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
||
65 | }; |
||
66 | }; |
||
67 | |||
68 | gpio_export { |
||
69 | compatible = "gpio-export"; |
||
70 | #size-cells = <0>; |
||
71 | |||
72 | display_data { |
||
73 | gpio-export,name = "display_data"; |
||
74 | gpio-export,output = <1>; |
||
75 | gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; |
||
76 | }; |
||
77 | |||
78 | display_clock { |
||
79 | gpio-export,name = "display_clock"; |
||
80 | gpio-export,output = <1>; |
||
81 | gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; |
||
82 | }; |
||
83 | |||
84 | display_blank { |
||
85 | gpio-export,name = "display_blank"; |
||
86 | gpio-export,output = <1>; |
||
87 | gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; |
||
88 | }; |
||
89 | }; |
||
90 | |||
3 | office | 91 | gpio-keys-polled { |
1 | office | 92 | compatible = "gpio-keys-polled"; |
3 | office | 93 | #address-cells = <1>; |
94 | #size-cells = <0>; |
||
1 | office | 95 | poll-interval = <20>; |
96 | |||
97 | reset_wps { |
||
98 | label = "reset_wps"; |
||
99 | gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
||
100 | linux,code = <KEY_RESTART>; |
||
101 | }; |
||
102 | |||
103 | wlan { |
||
104 | label = "wlan"; |
||
105 | gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
||
106 | linux,code = <BTN_0>; |
||
107 | }; |
||
108 | }; |
||
109 | }; |
||
110 | |||
111 | &pinctrl { |
||
112 | state_default: pinctrl0 { |
||
113 | gpio { |
||
114 | ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf"; |
||
115 | ralink,function = "gpio"; |
||
116 | }; |
||
117 | }; |
||
118 | }; |
||
119 | |||
120 | ðernet { |
||
121 | mtd-mac-address = <&factory 0x2e>; |
||
122 | }; |
||
123 | |||
124 | &esw { |
||
125 | mediatek,portmap = <0x3e>; |
||
126 | }; |
||
127 | |||
128 | &wmac { |
||
129 | ralink,mtd-eeprom = <&factory 0>; |
||
130 | }; |