OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3050.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "poray,ip2202", "ralink,rt3052-soc"; |
||
10 | model = "Poray IP2202"; |
||
11 | |||
12 | cfi@1f000000 { |
||
13 | compatible = "cfi-flash"; |
||
14 | reg = <0x1f000000 0x800000>; |
||
15 | bank-width = <2>; |
||
16 | device-width = <2>; |
||
3 | office | 17 | #address-cells = <1>; |
18 | #size-cells = <1>; |
||
1 | office | 19 | |
3 | office | 20 | partition@0 { |
21 | label = "u-boot"; |
||
22 | reg = <0x0 0x30000>; |
||
23 | read-only; |
||
24 | }; |
||
1 | office | 25 | |
3 | office | 26 | partition@30000 { |
27 | label = "u-boot-env"; |
||
28 | reg = <0x30000 0x10000>; |
||
29 | read-only; |
||
30 | }; |
||
1 | office | 31 | |
3 | office | 32 | factory: partition@40000 { |
33 | label = "factory"; |
||
34 | reg = <0x40000 0x10000>; |
||
35 | read-only; |
||
36 | }; |
||
1 | office | 37 | |
3 | office | 38 | partition@50000 { |
39 | label = "firmware"; |
||
40 | reg = <0x50000 0x7b0000>; |
||
1 | office | 41 | }; |
42 | }; |
||
43 | |||
3 | office | 44 | gpio-leds { |
1 | office | 45 | compatible = "gpio-leds"; |
46 | |||
3 | office | 47 | run { |
1 | office | 48 | label = "ip2202:green:run"; |
49 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
50 | }; |
||
51 | |||
52 | net { |
||
53 | label = "ip2202:amber:net"; |
||
54 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
||
55 | }; |
||
56 | }; |
||
57 | |||
3 | office | 58 | gpio-keys-polled { |
1 | office | 59 | compatible = "gpio-keys-polled"; |
3 | office | 60 | #address-cells = <1>; |
61 | #size-cells = <0>; |
||
1 | office | 62 | poll-interval = <20>; |
63 | |||
64 | reset { |
||
65 | label = "reset"; |
||
66 | gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
||
67 | linux,code = <KEY_RESTART>; |
||
68 | }; |
||
69 | }; |
||
70 | }; |
||
71 | |||
72 | &pinctrl { |
||
73 | state_default: pinctrl0 { |
||
74 | gpio { |
||
75 | ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf"; |
||
76 | ralink,function = "gpio"; |
||
77 | }; |
||
78 | }; |
||
79 | }; |
||
80 | |||
81 | ðernet { |
||
82 | mtd-mac-address = <&factory 0x28>; |
||
83 | }; |
||
84 | |||
85 | &esw { |
||
86 | mediatek,portmap = <0x2f>; |
||
87 | }; |
||
88 | |||
89 | &otg { |
||
90 | status = "okay"; |
||
91 | }; |