OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | #include "mt7620a.dtsi" |
2 | |||
3 | #include <dt-bindings/gpio/gpio.h> |
||
4 | #include <dt-bindings/input/input.h> |
||
5 | |||
6 | / { |
||
7 | compatible = "hiwifi,hc5x61", "ralink,mt7620a-soc"; |
||
8 | |||
9 | chosen { |
||
10 | bootargs = "console=ttyS0,115200"; |
||
11 | }; |
||
12 | |||
3 | office | 13 | gpio-keys-polled { |
1 | office | 14 | compatible = "gpio-keys-polled"; |
3 | office | 15 | #address-cells = <1>; |
16 | #size-cells = <0>; |
||
1 | office | 17 | poll-interval = <20>; |
18 | |||
19 | reset { |
||
20 | label = "reset"; |
||
21 | gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
||
22 | linux,code = <KEY_RESTART>; |
||
23 | }; |
||
24 | }; |
||
25 | |||
26 | gpio_export { |
||
27 | compatible = "gpio-export"; |
||
28 | #size-cells = <0>; |
||
29 | |||
30 | usbpower { |
||
31 | gpio-export,name = "usbpower"; |
||
32 | gpio-export,output = <1>; |
||
33 | gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; |
||
34 | }; |
||
35 | }; |
||
36 | }; |
||
37 | |||
38 | &sysc { |
||
39 | ralink,gpiomux = "i2c", "jtag"; |
||
40 | ralink,uartmux = "gpio"; |
||
41 | ralink,wdtmux = <1>; |
||
42 | }; |
||
43 | |||
44 | &gpio0 { |
||
45 | status = "okay"; |
||
46 | }; |
||
47 | |||
48 | &gpio2 { |
||
49 | status = "okay"; |
||
50 | }; |
||
51 | |||
52 | &gpio3 { |
||
53 | status = "okay"; |
||
54 | }; |
||
55 | |||
56 | &spi0 { |
||
57 | status = "okay"; |
||
58 | |||
59 | m25p80@0 { |
||
3 | office | 60 | #address-cells = <1>; |
61 | #size-cells = <1>; |
||
1 | office | 62 | compatible = "jedec,spi-nor"; |
63 | reg = <0>; |
||
64 | spi-max-frequency = <10000000>; |
||
65 | |||
3 | office | 66 | partition@0 { |
67 | label = "u-boot"; |
||
68 | reg = <0x0 0x30000>; |
||
69 | }; |
||
1 | office | 70 | |
3 | office | 71 | partition@30000 { |
72 | label = "u-boot-env"; |
||
73 | reg = <0x30000 0x10000>; |
||
74 | read-only; |
||
75 | }; |
||
1 | office | 76 | |
3 | office | 77 | factory: partition@40000 { |
78 | label = "factory"; |
||
79 | reg = <0x40000 0x10000>; |
||
80 | }; |
||
1 | office | 81 | |
3 | office | 82 | partition@50000 { |
83 | label = "firmware"; |
||
84 | reg = <0x50000 0xf80000>; |
||
85 | }; |
||
1 | office | 86 | |
3 | office | 87 | partition@fd0000 { |
88 | label = "hwf_config"; |
||
89 | reg = <0xfd0000 0x10000>; |
||
90 | }; |
||
1 | office | 91 | |
3 | office | 92 | bdinfo: partition@fe0000 { |
93 | label = "bdinfo"; |
||
94 | reg = <0xfe0000 0x10000>; |
||
95 | }; |
||
1 | office | 96 | |
3 | office | 97 | partition@ff0000 { |
98 | label = "backup"; |
||
99 | reg = <0xff0000 0x10000>; |
||
1 | office | 100 | }; |
101 | }; |
||
102 | }; |
||
103 | |||
3 | office | 104 | &ehci { |
105 | status = "okay"; |
||
106 | }; |
||
107 | |||
108 | &ohci { |
||
109 | status = "okay"; |
||
110 | }; |
||
111 | |||
1 | office | 112 | ðernet { |
113 | pinctrl-names = "default"; |
||
114 | pinctrl-0 = <&ephy_pins>; |
||
115 | mtd-mac-address = <&factory 0x4>; |
||
116 | mediatek,portmap = "wllll"; |
||
117 | }; |
||
118 | |||
119 | &sdhci { |
||
120 | status = "okay"; |
||
121 | }; |
||
122 | |||
123 | &wmac { |
||
124 | ralink,mtd-eeprom = <&factory 0>; |
||
125 | pinctrl-names = "default"; |
||
126 | pinctrl-0 = <&pa_pins>; |
||
127 | }; |
||
128 | |||
3 | office | 129 | &pcie { |
130 | status = "okay"; |
||
131 | }; |
||
132 | |||
1 | office | 133 | &pinctrl { |
134 | state_default: pinctrl0 { |
||
135 | gpio { |
||
3 | office | 136 | ralink,group = "uartf", "wled", "nd_sd"; |
1 | office | 137 | ralink,function = "gpio"; |
138 | }; |
||
139 | }; |
||
140 | }; |