OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3050.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "arcwireless,freestation5", "ralink,rt3050-soc"; |
||
10 | model = "ARC FreeStation5"; |
||
11 | |||
12 | chosen { |
||
13 | bootargs = "console=ttyS0,115200"; |
||
14 | }; |
||
15 | |||
16 | cfi@1f000000 { |
||
17 | compatible = "cfi-flash"; |
||
18 | reg = <0x1f000000 0x800000>; |
||
19 | bank-width = <2>; |
||
20 | device-width = <2>; |
||
3 | office | 21 | #address-cells = <1>; |
22 | #size-cells = <1>; |
||
1 | office | 23 | |
3 | office | 24 | partition@0 { |
25 | label = "u-boot"; |
||
26 | reg = <0x0 0x30000>; |
||
27 | read-only; |
||
28 | }; |
||
1 | office | 29 | |
3 | office | 30 | partition@30000 { |
31 | label = "u-boot-env"; |
||
32 | reg = <0x30000 0x10000>; |
||
33 | read-only; |
||
34 | }; |
||
1 | office | 35 | |
3 | office | 36 | factory: partition@40000 { |
37 | label = "factory"; |
||
38 | reg = <0x40000 0x10000>; |
||
39 | read-only; |
||
40 | }; |
||
1 | office | 41 | |
3 | office | 42 | partition@50000 { |
43 | label = "firmware"; |
||
44 | reg = <0x50000 0x7b0000>; |
||
1 | office | 45 | }; |
46 | }; |
||
47 | |||
48 | gpio-export { |
||
49 | compatible = "gpio-export"; |
||
50 | |||
3 | office | 51 | // Used to enable power-over-ethernet passthrough from port0 to port1. |
52 | // Disable passthrough by default to prevent accidental equipment damage. |
||
1 | office | 53 | poe { |
54 | gpio-export,name = "poe-passthrough"; |
||
3 | office | 55 | gpio-export,output = <1>; // OUT_INIT_HIGH |
56 | gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; // GPIO 11, ACTIVE_LOW |
||
1 | office | 57 | }; |
58 | }; |
||
59 | |||
3 | office | 60 | gpio-leds { |
1 | office | 61 | compatible = "gpio-leds"; |
62 | |||
3 | office | 63 | // The following leds are defined in the ArcOS firmware, but reportedly |
64 | // not present in the Freestation5 device. |
||
1 | office | 65 | wifi { |
66 | label = "freestation5:unknown:wifi"; |
||
67 | gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; |
||
68 | }; |
||
69 | |||
70 | powerg { |
||
71 | label = "freestation5:unknown:powerg"; |
||
72 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
73 | }; |
||
74 | |||
75 | usb { |
||
76 | label = "freestation5:unknown:usb"; |
||
77 | gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; |
||
78 | }; |
||
79 | }; |
||
80 | }; |
||
81 | |||
82 | &pinctrl { |
||
83 | state_default: pinctrl0 { |
||
84 | gpio { |
||
85 | ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf"; |
||
86 | ralink,function = "gpio"; |
||
87 | }; |
||
88 | }; |
||
89 | }; |
||
90 | |||
91 | ðernet { |
||
92 | mtd-mac-address = <&factory 0x4>; |
||
93 | }; |
||
94 | |||
95 | &esw { |
||
96 | mediatek,portmap = <0x01>; |
||
97 | }; |
||
98 | |||
99 | &wmac { |
||
100 | ralink,mtd-eeprom = <&factory 0>; |
||
101 | }; |
||
102 | |||
103 | &otg { |
||
104 | status = "okay"; |
||
105 | }; |