OpenWrt – Blame information for rev 3

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 /dts-v1/;
2  
3 #include "rt3050.dtsi"
4  
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/input.h>
7  
8 / {
9 compatible = "fon,fonera20n", "ralink,rt3052-soc";
10 model = "La Fonera 2.0N";
11  
12 cfi@1f000000 {
13 compatible = "cfi-flash";
14 reg = <0x1f000000 0x800000>;
15 bank-width = <2>;
16 device-width = <2>;
3 office 17 #address-cells = <1>;
18 #size-cells = <1>;
1 office 19  
3 office 20 partition@0 {
21 label = "u-boot";
22 reg = <0x0 0x30000>;
23 read-only;
24 };
1 office 25  
3 office 26 partition@30000 {
27 label = "u-boot-env";
28 reg = <0x30000 0x10000>;
29 read-only;
30 };
1 office 31  
3 office 32 factory: partition@40000 {
33 label = "factory";
34 reg = <0x40000 0x10000>;
35 read-only;
36 };
1 office 37  
3 office 38 partition@50000 {
39 label = "firmware";
40 reg = <0x50000 0x7b0000>;
1 office 41 };
42 };
43  
3 office 44 gpio-leds {
1 office 45 compatible = "gpio-leds";
46  
47 wifi {
48 label = "fonera20n:orange:wifi";
49 gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
50 };
51  
3 office 52 power {
1 office 53 label = "fonera20n:green:power";
54 gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
55 };
56  
57 usb {
58 label = "fonera20n:orange:usb";
59 gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
60 };
61 };
62  
3 office 63 gpio-keys-polled {
1 office 64 compatible = "gpio-keys-polled";
3 office 65 #address-cells = <1>;
66 #size-cells = <0>;
1 office 67 poll-interval = <20>;
68  
69 reset {
70 label = "reset";
71 gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
72 linux,code = <KEY_RESTART>;
73 };
74  
75 switch {
76 label = "switch";
77 gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
78 linux,code = <KEY_RFKILL>;
79 linux,input-type = <EV_SW>;
80 };
81 };
82 };
83  
84 &pinctrl {
85 state_default: pinctrl0 {
86 gpio {
87 ralink,group = "i2c", "spi", "jtag", "mdio", "rgmii", "uartf";
88 ralink,function = "gpio";
89 };
90 };
91 };
92  
93 &ethernet {
94 mtd-mac-address = <&factory 0x28>;
95 };
96  
97 &esw {
98 mediatek,portmap = <0x2f>;
99  
100 port@0 {
101 compatible = "swconfig,port";
102 swconfig,segment = "lan";
103 swconfig,portmap = <0 4>;
104 };
105  
106 port@1 {
107 compatible = "swconfig,port";
108 swconfig,segment = "lan";
109 swconfig,portmap = <1 3>;
110 };
111  
112 port@2 {
113 compatible = "swconfig,port";
114 swconfig,segment = "lan";
115 swconfig,portmap = <2 2>;
116 };
117  
118 port@3 {
119 compatible = "swconfig,port";
120 swconfig,segment = "lan";
121 swconfig,portmap = <3 1>;
122 };
123  
124 port@4 {
125 compatible = "swconfig,port";
126 swconfig,segment = "wan";
127 swconfig,portmap = <4 0>;
128 };
129 };
130  
131 &wmac {
132 ralink,mtd-eeprom = <&factory 0>;
133 };
134  
135 &otg {
136 status = "okay";
137 };