OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3050.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "belkin,f5d8235-v2", "ralink,rt3052-soc"; |
||
10 | model = "Belkin F5D8235 v2"; |
||
11 | |||
12 | aliases { |
||
13 | led-boot = &led_router; |
||
14 | led-failsafe = &led_router; |
||
15 | led-running = &led_router; |
||
16 | led-upgrade = &led_router; |
||
17 | }; |
||
18 | |||
19 | cfi@1f000000 { |
||
20 | compatible = "cfi-flash"; |
||
21 | reg = <0x1f000000 0x800000>; |
||
22 | bank-width = <2>; |
||
23 | device-width = <2>; |
||
24 | |||
25 | partitions { |
||
26 | compatible = "fixed-partitions"; |
||
27 | #address-cells = <1>; |
||
28 | #size-cells = <1>; |
||
29 | |||
30 | uboot: partition@0 { |
||
31 | label = "uboot"; |
||
32 | reg = <0x0 0x50000>; |
||
33 | read-only; |
||
34 | }; |
||
35 | |||
36 | partition@50000 { |
||
37 | compatible = "denx,uimage"; |
||
38 | label = "firmware"; |
||
39 | reg = <0x50000 0x790000>; |
||
40 | }; |
||
41 | |||
42 | partition@7e0000 { |
||
43 | label = "nvram"; |
||
44 | reg = <0x7e0000 0x10000>; |
||
45 | }; |
||
46 | |||
47 | factory: partition@7f0000 { |
||
48 | label = "factory"; |
||
49 | reg = <0x7f0000 0x10000>; |
||
50 | }; |
||
51 | }; |
||
52 | }; |
||
53 | |||
54 | rtl8366rb { |
||
55 | compatible = "realtek,rtl8366rb"; |
||
56 | gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>; |
||
57 | gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
||
58 | }; |
||
59 | |||
60 | leds { |
||
61 | compatible = "gpio-leds"; |
||
62 | |||
63 | internet { |
||
64 | label = "f5d8235-v2:blue:internet"; |
||
65 | gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; |
||
66 | }; |
||
67 | |||
68 | internet2 { |
||
69 | label = "f5d8235-v2:amber:internet"; |
||
70 | gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; |
||
71 | }; |
||
72 | |||
73 | modem { |
||
74 | label = "f5d8235-v2:blue:modem"; |
||
75 | gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
||
76 | }; |
||
77 | |||
78 | modem2 { |
||
79 | label = "f5d8235-v2:amber:modem"; |
||
80 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
||
81 | }; |
||
82 | |||
83 | led_router: router { |
||
84 | label = "f5d8235-v2:blue:router"; |
||
85 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
86 | }; |
||
87 | |||
88 | storage { |
||
89 | label = "f5d8235-v2:blue:storage"; |
||
90 | gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; |
||
91 | trigger-sources = <&otg_port1>; |
||
92 | linux,default-trigger = "usbport"; |
||
93 | }; |
||
94 | |||
95 | storage2 { |
||
96 | label = "f5d8235-v2:amber:storage"; |
||
97 | gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; |
||
98 | }; |
||
99 | |||
100 | security { |
||
101 | label = "f5d8235-v2:blue:security"; |
||
102 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
||
103 | }; |
||
104 | |||
105 | security2 { |
||
106 | label = "f5d8235-v2:amber:security"; |
||
107 | gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
||
108 | }; |
||
109 | }; |
||
110 | }; |
||
111 | |||
112 | &pinctrl { |
||
113 | state_default: pinctrl0 { |
||
114 | gpio { |
||
115 | ralink,group = "spi", "i2c", "jtag", "mdio", "uartf"; |
||
116 | ralink,function = "gpio"; |
||
117 | }; |
||
118 | }; |
||
119 | }; |
||
120 | |||
121 | ðernet { |
||
122 | mtd-mac-address = <&uboot 0x40004>; |
||
123 | pinctrl-names = "default"; |
||
124 | pinctrl-0 = <&rgmii_pins>; |
||
125 | }; |
||
126 | |||
127 | &esw { |
||
128 | ralink,rgmii = <1>; |
||
129 | mediatek,portmap = <0x3f>; |
||
130 | ralink,fct2 = <0x0002500c>; |
||
131 | /* |
||
132 | * ext phy base addr 31, rx/tx clock skew 0, |
||
133 | * turbo mii off, rgmi 3.3v off, port 5 polling off |
||
134 | * port5: enabled, gige, full-duplex, rx/tx-flow-control |
||
135 | * port6: enabled, gige, full-duplex, rx/tx-flow-control |
||
136 | */ |
||
137 | ralink,fpa2 = <0x1f003fff>; |
||
138 | }; |
||
139 | |||
140 | &wmac { |
||
141 | ralink,mtd-eeprom = <&uboot 0x40000>; |
||
142 | }; |
||
143 | |||
144 | &otg { |
||
145 | status = "okay"; |
||
146 | }; |