OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "mt7620a.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "dlink,dir-810l", "ralink,mt7620a-soc"; |
||
10 | model = "D-Link DIR-810L"; |
||
11 | |||
3 | office | 12 | gpio-keys-polled { |
1 | office | 13 | compatible = "gpio-keys-polled"; |
3 | office | 14 | #address-cells = <1>; |
15 | #size-cells = <0>; |
||
1 | office | 16 | poll-interval = <20>; |
17 | |||
18 | reset { |
||
19 | label = "reset"; |
||
20 | gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
||
21 | linux,code = <BTN_0>; |
||
22 | }; |
||
23 | |||
24 | wps { |
||
25 | label = "wps"; |
||
26 | gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
||
27 | linux,code = <BTN_0>; |
||
28 | }; |
||
29 | }; |
||
30 | |||
3 | office | 31 | gpio-leds { |
1 | office | 32 | compatible = "gpio-leds"; |
33 | |||
3 | office | 34 | power { |
1 | office | 35 | label = "dir-810l:green:power"; |
36 | gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; |
||
37 | }; |
||
38 | |||
39 | wan { |
||
40 | label = "dir-810l:orange:wan"; |
||
41 | gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; |
||
42 | }; |
||
43 | |||
3 | office | 44 | status { |
1 | office | 45 | label = "dir-810l:orange:power"; |
46 | gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; |
||
47 | }; |
||
48 | }; |
||
49 | }; |
||
50 | |||
51 | &spi0 { |
||
52 | status = "okay"; |
||
53 | |||
54 | m25p80@0 { |
||
3 | office | 55 | #address-cells = <1>; |
56 | #size-cells = <1>; |
||
1 | office | 57 | compatible = "jedec,spi-nor"; |
58 | reg = <0>; |
||
59 | spi-max-frequency = <10000000>; |
||
60 | |||
3 | office | 61 | partition@0 { |
62 | label = "u-boot"; |
||
63 | reg = <0x0 0x30000>; |
||
64 | read-only; |
||
65 | }; |
||
1 | office | 66 | |
3 | office | 67 | partition@30000 { |
68 | label = "u-boot-env"; |
||
69 | reg = <0x30000 0x10000>; |
||
70 | read-only; |
||
71 | }; |
||
1 | office | 72 | |
3 | office | 73 | factory: partition@40000 { |
74 | label = "factory"; |
||
75 | reg = <0x40000 0x10000>; |
||
76 | read-only; |
||
77 | }; |
||
1 | office | 78 | |
3 | office | 79 | factory5g: partition@50000 { |
80 | label = "factory5g"; |
||
81 | reg = <0x50000 0x10000>; |
||
82 | read-only; |
||
83 | }; |
||
1 | office | 84 | |
3 | office | 85 | partition@60000 { |
86 | label = "Wolf_Config"; |
||
87 | reg = <0x60000 0x10000>; |
||
88 | read-only; |
||
89 | }; |
||
1 | office | 90 | |
3 | office | 91 | partition@70000 { |
92 | label = "MyDlink"; |
||
93 | reg = <0x70000 0x80000>; |
||
94 | read-only; |
||
95 | }; |
||
1 | office | 96 | |
3 | office | 97 | partition@e0000 { |
98 | label = "Jffs2"; |
||
99 | reg = <0xe0000 0x80000>; |
||
100 | read-only; |
||
101 | }; |
||
1 | office | 102 | |
3 | office | 103 | partition@170000 { |
104 | label = "firmware"; |
||
105 | reg = <0x170000 0x690000>; |
||
1 | office | 106 | }; |
107 | }; |
||
108 | }; |
||
109 | |||
110 | &pinctrl { |
||
111 | state_default: pinctrl0 { |
||
112 | gpio { |
||
113 | ralink,group = "mdio", "rgmii1", "i2c", "wled", "uartf"; |
||
114 | ralink,function = "gpio"; |
||
115 | }; |
||
116 | }; |
||
117 | }; |
||
118 | |||
119 | ðernet { |
||
120 | mtd-mac-address = <&factory 0x28>; |
||
121 | mediatek,portmap = "llllw"; |
||
122 | }; |
||
123 | |||
124 | &gsw { |
||
125 | mediatek,port4 = "ephy"; |
||
126 | pinctrl-names = "default"; |
||
127 | pinctrl-0 = <&ephy_pins>; |
||
128 | }; |
||
129 | |||
130 | &pcie { |
||
131 | status = "okay"; |
||
132 | }; |
||
133 | |||
134 | &wmac { |
||
135 | ralink,mtd-eeprom = <&factory 0>; |
||
136 | }; |