OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt2880.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "dlink,dap-1522-a1", "ralink,rt2880-soc"; |
||
10 | model = "D-Link DAP-1522 A1"; |
||
11 | |||
12 | aliases { |
||
13 | led-boot = &led_status; |
||
14 | led-failsafe = &led_status; |
||
15 | led-running = &led_status; |
||
16 | led-upgrade = &led_status; |
||
17 | }; |
||
18 | |||
19 | cfi@bc400000 { |
||
20 | compatible = "cfi-flash"; |
||
21 | reg = <0xbc400000 0x800000>; |
||
22 | bank-width = <2>; |
||
23 | device-width = <2>; |
||
24 | |||
25 | partitions { |
||
26 | compatible = "fixed-partitions"; |
||
27 | #address-cells = <1>; |
||
28 | #size-cells = <1>; |
||
29 | |||
30 | partition@0 { |
||
31 | label = "uboot"; |
||
32 | reg = <0x0 0x30000>; |
||
33 | read-only; |
||
34 | }; |
||
35 | |||
36 | factory: partition@30000 { |
||
37 | label = "factory"; |
||
38 | reg = <0x30000 0x10000>; |
||
39 | read-only; |
||
40 | }; |
||
41 | |||
42 | partition@40000 { |
||
43 | compatible = "wrg"; |
||
44 | label = "firmware"; |
||
45 | reg = <0x40000 0x3a0000>; |
||
46 | }; |
||
47 | }; |
||
48 | }; |
||
49 | |||
50 | rtl8366s { |
||
51 | compatible = "realtek,rtl8366s"; |
||
52 | gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>; |
||
53 | gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
||
54 | }; |
||
55 | |||
56 | keys { |
||
57 | compatible = "gpio-keys-polled"; |
||
58 | poll-interval = <100>; |
||
59 | |||
60 | reset { |
||
61 | label = "reset"; |
||
62 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
63 | linux,code = <KEY_RESTART>; |
||
64 | }; |
||
65 | |||
66 | wps { |
||
67 | label = "wps"; |
||
68 | gpios = <&gpio2 16 GPIO_ACTIVE_LOW>; |
||
69 | linux,code = <KEY_WPS_BUTTON>; |
||
70 | }; |
||
71 | |||
72 | ap { |
||
73 | label = "ap"; |
||
74 | gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; |
||
75 | linux,code = <BTN_0>; |
||
76 | linux,input-type = <EV_SW>; |
||
77 | }; |
||
78 | |||
79 | bridge { |
||
80 | label = "bridge"; |
||
81 | gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; |
||
82 | linux,code = <BTN_1>; |
||
83 | linux,input-type = <EV_SW>; |
||
84 | }; |
||
85 | }; |
||
86 | |||
87 | leds { |
||
88 | compatible = "gpio-leds"; |
||
89 | |||
90 | wps { |
||
91 | label = "dap-1522-a1:blue:wps"; |
||
92 | gpios = <&gpio2 17 GPIO_ACTIVE_LOW>; |
||
93 | }; |
||
94 | |||
95 | ap { |
||
96 | label = "dap-1522-a1:blue:ap"; |
||
97 | gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; |
||
98 | }; |
||
99 | |||
100 | sta { |
||
101 | label = "dap-1522-a1:red:sta"; |
||
102 | gpios = <&gpio2 19 GPIO_ACTIVE_LOW>; |
||
103 | }; |
||
104 | |||
105 | led_status: status { |
||
106 | label = "dap-1522-a1:blue:status"; |
||
107 | gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; |
||
108 | }; |
||
109 | }; |
||
110 | }; |
||
111 | |||
112 | &gpio0 { |
||
113 | status = "okay"; |
||
114 | }; |
||
115 | |||
116 | &gpio2 { |
||
117 | status = "okay"; |
||
118 | }; |
||
119 | |||
120 | &pinctrl { |
||
121 | state_default: pinctrl0 { |
||
122 | gpio { |
||
123 | ralink,group = "i2c", "uartlite", "pci"; |
||
124 | ralink,function = "gpio"; |
||
125 | }; |
||
126 | }; |
||
127 | }; |
||
128 | |||
129 | ðernet { |
||
130 | status = "okay"; |
||
131 | mtd-mac-address = <&factory 0x2004>; |
||
132 | |||
133 | port@0 { |
||
134 | mediatek,fixed-link = <1000 1 1 1>; |
||
135 | }; |
||
136 | |||
137 | mdio-bus { |
||
138 | status = "okay"; |
||
139 | |||
140 | phy0: ethernet-phy@0 { |
||
141 | phy-mode = "mii"; |
||
142 | reg = <0>; |
||
143 | }; |
||
144 | }; |
||
145 | }; |
||
146 | |||
147 | &wmac { |
||
148 | ralink,mtd-eeprom = <&factory 0x2000>; |
||
149 | }; |