OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt2880.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "dlink,dap-1522-a1", "ralink,rt2880-soc"; |
||
10 | model = "D-Link DAP-1522 A1"; |
||
11 | |||
12 | cfi@bc400000 { |
||
13 | compatible = "cfi-flash"; |
||
14 | reg = <0xbc400000 0x800000>; |
||
15 | bank-width = <2>; |
||
16 | device-width = <2>; |
||
3 | office | 17 | #address-cells = <1>; |
18 | #size-cells = <1>; |
||
1 | office | 19 | |
3 | office | 20 | partition@0 { |
21 | label = "uboot"; |
||
22 | reg = <0x0 0x30000>; |
||
23 | read-only; |
||
24 | }; |
||
1 | office | 25 | |
3 | office | 26 | factory: partition@30000 { |
27 | label = "factory"; |
||
28 | reg = <0x30000 0x10000>; |
||
29 | read-only; |
||
30 | }; |
||
1 | office | 31 | |
3 | office | 32 | partition@40000 { |
33 | label = "firmware"; |
||
34 | reg = <0x40000 0x3a0000>; |
||
1 | office | 35 | }; |
36 | }; |
||
37 | |||
38 | rtl8366s { |
||
39 | compatible = "realtek,rtl8366s"; |
||
40 | gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>; |
||
41 | gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
||
42 | }; |
||
43 | |||
3 | office | 44 | gpio-keys-polled { |
1 | office | 45 | compatible = "gpio-keys-polled"; |
3 | office | 46 | #address-cells = <1>; |
47 | #size-cells = <0>; |
||
1 | office | 48 | poll-interval = <100>; |
49 | |||
50 | reset { |
||
51 | label = "reset"; |
||
52 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
53 | linux,code = <KEY_RESTART>; |
||
54 | }; |
||
55 | |||
56 | wps { |
||
57 | label = "wps"; |
||
58 | gpios = <&gpio2 16 GPIO_ACTIVE_LOW>; |
||
59 | linux,code = <KEY_WPS_BUTTON>; |
||
60 | }; |
||
61 | |||
62 | ap { |
||
63 | label = "ap"; |
||
64 | gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; |
||
65 | linux,code = <BTN_0>; |
||
66 | linux,input-type = <EV_SW>; |
||
67 | }; |
||
68 | |||
69 | bridge { |
||
70 | label = "bridge"; |
||
71 | gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; |
||
72 | linux,code = <BTN_1>; |
||
73 | linux,input-type = <EV_SW>; |
||
74 | }; |
||
75 | }; |
||
76 | |||
3 | office | 77 | gpio-leds { |
1 | office | 78 | compatible = "gpio-leds"; |
79 | |||
80 | wps { |
||
81 | label = "dap-1522-a1:blue:wps"; |
||
82 | gpios = <&gpio2 17 GPIO_ACTIVE_LOW>; |
||
83 | }; |
||
84 | |||
85 | ap { |
||
86 | label = "dap-1522-a1:blue:ap"; |
||
87 | gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; |
||
88 | }; |
||
89 | |||
90 | sta { |
||
91 | label = "dap-1522-a1:red:sta"; |
||
92 | gpios = <&gpio2 19 GPIO_ACTIVE_LOW>; |
||
93 | }; |
||
94 | |||
3 | office | 95 | status { |
1 | office | 96 | label = "dap-1522-a1:blue:status"; |
97 | gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; |
||
98 | }; |
||
99 | }; |
||
100 | }; |
||
101 | |||
102 | &gpio0 { |
||
103 | status = "okay"; |
||
104 | }; |
||
105 | |||
106 | &gpio2 { |
||
107 | status = "okay"; |
||
108 | }; |
||
109 | |||
110 | &pinctrl { |
||
111 | state_default: pinctrl0 { |
||
112 | gpio { |
||
113 | ralink,group = "i2c", "uartlite", "pci"; |
||
114 | ralink,function = "gpio"; |
||
115 | }; |
||
116 | }; |
||
117 | }; |
||
118 | |||
119 | ðernet { |
||
120 | status = "okay"; |
||
121 | mtd-mac-address = <&factory 0x2004>; |
||
122 | |||
123 | port@0 { |
||
124 | mediatek,fixed-link = <1000 1 1 1>; |
||
125 | }; |
||
126 | |||
127 | mdio-bus { |
||
128 | status = "okay"; |
||
129 | |||
130 | phy0: ethernet-phy@0 { |
||
131 | phy-mode = "mii"; |
||
132 | reg = <0>; |
||
133 | }; |
||
134 | }; |
||
135 | }; |
||
136 | |||
137 | &wmac { |
||
138 | ralink,mtd-eeprom = <&factory 0x2000>; |
||
139 | }; |