OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt3883.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "edimax,br-6475nd", "ralink,rt3883-soc"; |
||
10 | model = "Edimax BR-6475nD"; |
||
11 | |||
3 | office | 12 | gpio-keys-polled { |
1 | office | 13 | compatible = "gpio-keys-polled"; |
3 | office | 14 | #address-cells = <1>; |
15 | #size-cells = <0>; |
||
1 | office | 16 | poll-interval = <100>; |
17 | |||
18 | reset { |
||
19 | label = "reset"; |
||
20 | gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; |
||
21 | linux,code = <KEY_RESTART>; |
||
22 | }; |
||
23 | |||
24 | rfkill { |
||
25 | label = "rfkill"; |
||
26 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
27 | linux,input-type = <EV_SW>; |
||
28 | linux,code = <KEY_RFKILL>; |
||
29 | }; |
||
30 | }; |
||
31 | |||
3 | office | 32 | gpio-leds { |
1 | office | 33 | compatible = "gpio-leds"; |
34 | |||
3 | office | 35 | power { |
1 | office | 36 | label = "br-6475nd:green:power"; |
37 | gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
||
38 | }; |
||
39 | |||
40 | wlan { |
||
41 | label = "br-6475nd:amber:wlan"; |
||
42 | gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
||
43 | }; |
||
44 | |||
45 | wlan_5ghz { |
||
46 | label = "br-6475nd:amber:wlan_5ghz"; |
||
47 | gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; |
||
48 | }; |
||
49 | }; |
||
50 | |||
51 | nor-flash@1c000000 { |
||
52 | compatible = "cfi-flash"; |
||
53 | reg = <0x1c000000 0x800000>; |
||
54 | bank-width = <2>; |
||
3 | office | 55 | #address-cells = <1>; |
56 | #size-cells = <1>; |
||
1 | office | 57 | |
3 | office | 58 | partition@0 { |
59 | reg = <0x00000000 0x00030000>; |
||
60 | label = "u-boot"; |
||
61 | read-only; |
||
62 | }; |
||
1 | office | 63 | |
3 | office | 64 | partition@30000 { |
65 | reg = <0x00030000 0x00010000>; |
||
66 | label = "nvram"; |
||
67 | read-only; |
||
68 | }; |
||
1 | office | 69 | |
3 | office | 70 | factory: partition@40000 { |
71 | reg = <0x00040000 0x00010000>; |
||
72 | label = "factory"; |
||
73 | read-only; |
||
74 | }; |
||
1 | office | 75 | |
3 | office | 76 | devdata: partition@50000 { |
77 | reg = <0x00050000 0x00020000>; |
||
78 | label = "devdata"; |
||
79 | read-only; |
||
80 | }; |
||
1 | office | 81 | |
3 | office | 82 | partition@70000 { |
83 | reg = <0x00070000 0x00790000>; |
||
84 | label = "firmware"; |
||
1 | office | 85 | }; |
86 | }; |
||
87 | |||
88 | rtl8367 { |
||
89 | compatible = "realtek,rtl8367"; |
||
90 | gpio-sda = <&gpio0 5 GPIO_ACTIVE_HIGH>; |
||
91 | gpio-sck = <&gpio0 4 GPIO_ACTIVE_HIGH>; |
||
92 | realtek,extif0 = <1 0 1 1 1 1 1 1 2>; |
||
93 | }; |
||
94 | |||
3 | office | 95 | /* Unclear if this is the correct gpio setup; the USB ports are |
96 | unpopulated on a stock BR-6475nD, even though the hardware exists |
||
97 | and the headers are there. */ |
||
1 | office | 98 | /* |
99 | gpio_export { |
||
100 | compatible = "gpio-export"; |
||
101 | #size-cells = <0>; |
||
102 | |||
103 | usb { |
||
104 | gpio-export,name="usb"; |
||
105 | gpio-export,output=<0>; |
||
106 | gpios = <&gpio0 19 GPIO_ACTIVE_LOW>; |
||
107 | }; |
||
108 | }; |
||
109 | */ |
||
110 | }; |
||
111 | |||
112 | &pinctrl { |
||
113 | state_default: pinctrl0 { |
||
114 | gpio { |
||
115 | ralink,group = "spi", "jtag", "uartf"; |
||
116 | ralink,function = "gpio"; |
||
117 | }; |
||
118 | }; |
||
119 | }; |
||
120 | |||
121 | &timer { |
||
122 | status = "okay"; |
||
123 | }; |
||
124 | |||
125 | &gpio1 { |
||
126 | status = "okay"; |
||
127 | }; |
||
128 | |||
129 | &uartlite { |
||
130 | status = "okay"; |
||
131 | }; |
||
132 | |||
133 | ðernet { |
||
134 | status = "okay"; |
||
135 | mtd-mac-address = <&devdata 0x0d>; |
||
136 | |||
137 | port@0 { |
||
138 | mediatek,fixed-link = <1000 1 1 1>; |
||
139 | }; |
||
140 | }; |
||
141 | |||
142 | &wmac { |
||
143 | status = "okay"; |
||
144 | ralink,mtd-eeprom = <&factory 0>; |
||
145 | }; |
||
146 | |||
147 | &pci { |
||
148 | status = "okay"; |
||
3 | office | 149 | pinctrl-names = "default"; |
150 | pinctrl-0 = <&pci_pins>; |
||
1 | office | 151 | |
3 | office | 152 | pci_pins: pci { |
153 | pci { |
||
154 | ralink,group = "pci"; |
||
155 | ralink,function = "pci-fnc"; |
||
156 | }; |
||
157 | }; |
||
1 | office | 158 | |
3 | office | 159 | host-bridge { |
160 | pci-bridge@1 { |
||
161 | status = "okay"; |
||
162 | |||
163 | wifi@0,0 { |
||
164 | compatible = "pci0,0"; |
||
165 | reg = <0x10000 0 0 0 0>; |
||
166 | ralink,5ghz = <0>; |
||
167 | ralink,mtd-eeprom = <&factory 0x8000>; |
||
168 | }; |
||
169 | }; |
||
1 | office | 170 | }; |
171 | }; |
||
172 | |||
173 | &ehci { |
||
174 | status = "okay"; |
||
175 | }; |
||
176 | |||
177 | &ohci { |
||
178 | status = "okay"; |
||
179 | }; |