OpenWrt – Blame information for rev 3

Subversion Repositories:
Rev:
Rev Author Line No. Line
1 office 1 /dts-v1/;
2  
3 #include "rt2880.dtsi"
4  
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/input.h>
7  
8 / {
9 compatible = "airlink101,ar725w", "ralink,rt2880-soc";
10 model = "Airlink101 AR725W";
11  
12 cfi@bdc00000 {
13 compatible = "cfi-flash";
14 reg = <0xbc400000 0x800000>;
15 bank-width = <2>;
3 office 16 #address-cells = <1>;
17 #size-cells = <1>;
1 office 18  
3 office 19 u-boot@0 {
20 reg = <0x0 0x30000>;
21 label = "u-boot";
22 read-only;
23 };
1 office 24  
3 office 25 u-boot-env@30000 {
26 reg = <0x30000 0x10000>;
27 label = "u-boot-env";
28 };
1 office 29  
3 office 30 factory: factory@40000 {
31 reg = <0x40000 0x10000>;
32 label = "factory";
33 read-only;
34 };
1 office 35  
3 office 36 firmware@50000 {
37 reg = <0x50000 0x3B0000>;
38 label = "firmware";
1 office 39 };
40 };
41  
3 office 42 gpio-leds {
1 office 43 compatible = "gpio-leds";
44  
3 office 45 status {
1 office 46 label = "ar725w:green:power";
47 gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
48 };
49  
50 wpsred {
51 label = "ar725w:red:wps";
52 gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
53 };
54  
55 wpsblue {
56 label = "ar725w:blue:wps";
57 gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
58 };
59 };
60  
3 office 61 gpio-keys-polled {
1 office 62 compatible = "gpio-keys-polled";
3 office 63 #address-cells = <1>;
64 #size-cells = <0>;
1 office 65 poll-interval = <100>;
66  
67 wps {
68 label = "wps";
69 gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
70 linux,code = <KEY_WPS_BUTTON>;
71 };
72  
73 reset {
74 label = "reset";
75 gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
76 linux,code = <KEY_RESTART>;
77 };
78 };
79 };
80  
81 &gpio0 {
82 status = "okay";
83 };
84  
85 &pinctrl {
86 state_default: pinctrl0 {
87 gpio {
88 ralink,group = "i2c", "spi", "uartlite";
89 ralink,function = "gpio";
90 };
91 };
92 };
93  
94 &ethernet {
95 status = "okay";
96 mtd-mac-address = <&factory 0x4>;
97  
98 port@0 {
99 phy-handle = <&phy0>;
100 phy-mode = "mii";
101 };
102  
103 mdio-bus {
104 status = "okay";
105  
106 phy0: ethernet-phy@0 {
107 phy-mode = "mii";
108 reg = <0>;
109 };
110 };
111 };
112  
113 &wmac {
114 status = "okay";
115 ralink,mtd-eeprom = <&factory 0>;
116 };