OpenWrt – Blame information for rev 1
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt2880.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "airlink101,ar725w", "ralink,rt2880-soc"; |
||
10 | model = "Airlink101 AR725W"; |
||
11 | |||
12 | aliases { |
||
13 | led-boot = &led_power; |
||
14 | led-failsafe = &led_power; |
||
15 | led-running = &led_power; |
||
16 | led-upgrade = &led_power; |
||
17 | }; |
||
18 | |||
19 | cfi@bdc00000 { |
||
20 | compatible = "cfi-flash"; |
||
21 | reg = <0xbc400000 0x800000>; |
||
22 | bank-width = <2>; |
||
23 | |||
24 | partitions { |
||
25 | compatible = "fixed-partitions"; |
||
26 | #address-cells = <1>; |
||
27 | #size-cells = <1>; |
||
28 | |||
29 | partition@0 { |
||
30 | reg = <0x0 0x30000>; |
||
31 | label = "u-boot"; |
||
32 | read-only; |
||
33 | }; |
||
34 | |||
35 | partition@30000 { |
||
36 | reg = <0x30000 0x10000>; |
||
37 | label = "u-boot-env"; |
||
38 | }; |
||
39 | |||
40 | factory: partition@40000 { |
||
41 | reg = <0x40000 0x10000>; |
||
42 | label = "factory"; |
||
43 | read-only; |
||
44 | }; |
||
45 | |||
46 | partition@50000 { |
||
47 | compatible = "denx,uimage"; |
||
48 | reg = <0x50000 0x3B0000>; |
||
49 | label = "firmware"; |
||
50 | }; |
||
51 | }; |
||
52 | }; |
||
53 | |||
54 | leds { |
||
55 | compatible = "gpio-leds"; |
||
56 | |||
57 | led_power: power { |
||
58 | label = "ar725w:green:power"; |
||
59 | gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; |
||
60 | }; |
||
61 | |||
62 | wpsred { |
||
63 | label = "ar725w:red:wps"; |
||
64 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
||
65 | }; |
||
66 | |||
67 | wpsblue { |
||
68 | label = "ar725w:blue:wps"; |
||
69 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
||
70 | }; |
||
71 | }; |
||
72 | |||
73 | keys { |
||
74 | compatible = "gpio-keys-polled"; |
||
75 | poll-interval = <100>; |
||
76 | |||
77 | wps { |
||
78 | label = "wps"; |
||
79 | gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
||
80 | linux,code = <KEY_WPS_BUTTON>; |
||
81 | }; |
||
82 | |||
83 | reset { |
||
84 | label = "reset"; |
||
85 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
86 | linux,code = <KEY_RESTART>; |
||
87 | }; |
||
88 | }; |
||
89 | }; |
||
90 | |||
91 | &gpio0 { |
||
92 | status = "okay"; |
||
93 | }; |
||
94 | |||
95 | &pinctrl { |
||
96 | state_default: pinctrl0 { |
||
97 | gpio { |
||
98 | ralink,group = "i2c", "spi", "uartlite"; |
||
99 | ralink,function = "gpio"; |
||
100 | }; |
||
101 | }; |
||
102 | }; |
||
103 | |||
104 | ðernet { |
||
105 | status = "okay"; |
||
106 | mtd-mac-address = <&factory 0x4>; |
||
107 | |||
108 | port@0 { |
||
109 | phy-handle = <&phy0>; |
||
110 | phy-mode = "mii"; |
||
111 | }; |
||
112 | |||
113 | mdio-bus { |
||
114 | status = "okay"; |
||
115 | |||
116 | phy0: ethernet-phy@0 { |
||
117 | phy-mode = "mii"; |
||
118 | reg = <0>; |
||
119 | }; |
||
120 | }; |
||
121 | }; |
||
122 | |||
123 | &wmac { |
||
124 | status = "okay"; |
||
125 | ralink,mtd-eeprom = <&factory 0>; |
||
126 | }; |