OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt2880.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "airlink101,ar725w", "ralink,rt2880-soc"; |
||
10 | model = "Airlink101 AR725W"; |
||
11 | |||
12 | cfi@bdc00000 { |
||
13 | compatible = "cfi-flash"; |
||
14 | reg = <0xbc400000 0x800000>; |
||
15 | bank-width = <2>; |
||
3 | office | 16 | #address-cells = <1>; |
17 | #size-cells = <1>; |
||
1 | office | 18 | |
3 | office | 19 | u-boot@0 { |
20 | reg = <0x0 0x30000>; |
||
21 | label = "u-boot"; |
||
22 | read-only; |
||
23 | }; |
||
1 | office | 24 | |
3 | office | 25 | u-boot-env@30000 { |
26 | reg = <0x30000 0x10000>; |
||
27 | label = "u-boot-env"; |
||
28 | }; |
||
1 | office | 29 | |
3 | office | 30 | factory: factory@40000 { |
31 | reg = <0x40000 0x10000>; |
||
32 | label = "factory"; |
||
33 | read-only; |
||
34 | }; |
||
1 | office | 35 | |
3 | office | 36 | firmware@50000 { |
37 | reg = <0x50000 0x3B0000>; |
||
38 | label = "firmware"; |
||
1 | office | 39 | }; |
40 | }; |
||
41 | |||
3 | office | 42 | gpio-leds { |
1 | office | 43 | compatible = "gpio-leds"; |
44 | |||
3 | office | 45 | status { |
1 | office | 46 | label = "ar725w:green:power"; |
47 | gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; |
||
48 | }; |
||
49 | |||
50 | wpsred { |
||
51 | label = "ar725w:red:wps"; |
||
52 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
||
53 | }; |
||
54 | |||
55 | wpsblue { |
||
56 | label = "ar725w:blue:wps"; |
||
57 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
||
58 | }; |
||
59 | }; |
||
60 | |||
3 | office | 61 | gpio-keys-polled { |
1 | office | 62 | compatible = "gpio-keys-polled"; |
3 | office | 63 | #address-cells = <1>; |
64 | #size-cells = <0>; |
||
1 | office | 65 | poll-interval = <100>; |
66 | |||
67 | wps { |
||
68 | label = "wps"; |
||
69 | gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
||
70 | linux,code = <KEY_WPS_BUTTON>; |
||
71 | }; |
||
72 | |||
73 | reset { |
||
74 | label = "reset"; |
||
75 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
76 | linux,code = <KEY_RESTART>; |
||
77 | }; |
||
78 | }; |
||
79 | }; |
||
80 | |||
81 | &gpio0 { |
||
82 | status = "okay"; |
||
83 | }; |
||
84 | |||
85 | &pinctrl { |
||
86 | state_default: pinctrl0 { |
||
87 | gpio { |
||
88 | ralink,group = "i2c", "spi", "uartlite"; |
||
89 | ralink,function = "gpio"; |
||
90 | }; |
||
91 | }; |
||
92 | }; |
||
93 | |||
94 | ðernet { |
||
95 | status = "okay"; |
||
96 | mtd-mac-address = <&factory 0x4>; |
||
97 | |||
98 | port@0 { |
||
99 | phy-handle = <&phy0>; |
||
100 | phy-mode = "mii"; |
||
101 | }; |
||
102 | |||
103 | mdio-bus { |
||
104 | status = "okay"; |
||
105 | |||
106 | phy0: ethernet-phy@0 { |
||
107 | phy-mode = "mii"; |
||
108 | reg = <0>; |
||
109 | }; |
||
110 | }; |
||
111 | }; |
||
112 | |||
113 | &wmac { |
||
114 | status = "okay"; |
||
115 | ralink,mtd-eeprom = <&factory 0>; |
||
116 | }; |