OpenWrt – Blame information for rev 3
?pathlinks?
Rev | Author | Line No. | Line |
---|---|---|---|
1 | office | 1 | /dts-v1/; |
2 | |||
3 | #include "rt2880.dtsi" |
||
4 | |||
5 | #include <dt-bindings/gpio/gpio.h> |
||
6 | #include <dt-bindings/input/input.h> |
||
7 | |||
8 | / { |
||
9 | compatible = "airlink101,ar670w", "ralink,rt2880-soc"; |
||
10 | model = "Airlink101 AR670W"; |
||
11 | |||
12 | cfi@bdc00000 { |
||
13 | compatible = "cfi-flash"; |
||
14 | reg = <0xbc400000 0x800000>; |
||
15 | bank-width = <2>; |
||
3 | office | 16 | #address-cells = <1>; |
17 | #size-cells = <1>; |
||
1 | office | 18 | |
3 | office | 19 | u-boot@0 { |
20 | reg = <0x0 0x30000>; |
||
21 | label = "u-boot"; |
||
22 | read-only; |
||
23 | }; |
||
1 | office | 24 | |
3 | office | 25 | factory: factory@30000 { |
26 | reg = <0x30000 0x10000>; |
||
27 | label = "factory"; |
||
28 | read-only; |
||
29 | }; |
||
1 | office | 30 | |
3 | office | 31 | firmware@40000 { |
32 | reg = <0x40000 0x3c0000>; |
||
33 | label = "firmware"; |
||
1 | office | 34 | }; |
35 | }; |
||
36 | |||
3 | office | 37 | gpio-leds { |
1 | office | 38 | compatible = "gpio-leds"; |
39 | |||
3 | office | 40 | status { |
1 | office | 41 | label = "ar670w:green:power"; |
42 | gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; |
||
43 | }; |
||
44 | |||
45 | wpsblue { |
||
46 | label = "ar670w:blue:wps"; |
||
47 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
||
48 | }; |
||
49 | }; |
||
50 | |||
3 | office | 51 | gpio-keys-polled { |
1 | office | 52 | compatible = "gpio-keys-polled"; |
3 | office | 53 | #address-cells = <1>; |
54 | #size-cells = <0>; |
||
1 | office | 55 | poll-interval = <100>; |
56 | |||
57 | wps { |
||
58 | label = "wps"; |
||
59 | gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
||
60 | linux,code = <KEY_WPS_BUTTON>; |
||
61 | }; |
||
62 | |||
63 | reset { |
||
64 | label = "reset"; |
||
65 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
||
66 | linux,code = <KEY_RESTART>; |
||
67 | }; |
||
68 | }; |
||
69 | }; |
||
70 | |||
71 | &gpio0 { |
||
72 | status = "okay"; |
||
73 | }; |
||
74 | |||
75 | &pinctrl { |
||
76 | state_default: pinctrl0 { |
||
77 | gpio { |
||
78 | ralink,group = "i2c", "spi", "uartlite"; |
||
79 | ralink,function = "gpio"; |
||
80 | }; |
||
81 | }; |
||
82 | }; |
||
83 | |||
84 | ðernet { |
||
85 | status = "okay"; |
||
86 | mtd-mac-address = <&factory 0x2004>; |
||
87 | |||
88 | port@0 { |
||
89 | phy-handle = <&phy0>; |
||
90 | phy-mode = "mii"; |
||
91 | }; |
||
92 | |||
93 | mdio-bus { |
||
94 | status = "okay"; |
||
95 | |||
96 | phy0: ethernet-phy@0 { |
||
97 | phy-mode = "mii"; |
||
98 | reg = <0>; |
||
99 | }; |
||
100 | }; |
||
101 | }; |
||
102 | |||
103 | &wmac { |
||
104 | status = "okay"; |
||
105 | ralink,mtd-eeprom = <&factory 0x2000>; |
||
106 | }; |